TMPM330FWFG Toshiba, TMPM330FWFG Datasheet - Page 421

• Manufacturer Part Number: TMPM330FWFG
• Description: Microcontrollers (MCU) MCU w/ ARM Cortex-M3 128K FLASH, 8K SRAM
• Manufacturer: Toshiba

Specifications of TMPM330FWFG

• Processor Series: TX03
• Core: ARM Cortex M3
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 128K
• Rom Type: Flash
• Ram (kbytes): 8K
• Number Of Pins: 100
• Package: LQFP(14×14)
• Vcc: 3V
• Cpu Mhz: 40
• Ssp (ch) Spi: -
• I2c/sio (ch): 3
• Uart/sio (ch): 3
• Usb: -
• Can: -
• Ethernet: -
• External Bus Interface: -
• Cs/wait Controller (ch): -
• Dma Controller: -
• 10-bit Da Converter: -
• 10-bit Ad Converter: 12
• 12-bit Ad Converter: -
• 16-bit Timer / Counter: 10
• Motor / Igbt Control: -
• Real Time Clock: 1
• Watchdog Timer: Y
• Osc Freq Detect: -
• Clock Gear: Y
• Low-power Hold Function: -
• Remote Control Interface: Y
• Hardware Cec Controller: Y
• Comparators: -
• Low-voltage Detector: -
• Etm Hardware Trace: 4-bit
• Lead Free Status / Rohs Status: Details

3)
Show Product Information Command (See Table 18-8)
1. The processing of the 1st and 2nd bytes are the same as for the RAM Transfer
2. The 3rd byte, which the target board receives from the controller, is a command. The
3. The 4th byte, transmitted from the target board to the controller, is an acknowledge
4. The 5th to 8th bytes, transmitted from the target board to the controller, are the data
5. The 9th to 20th bytes, transmitted from the target board to the controller, indicate the
command.
code for the Show Product Information command is 30H.
response to the 3rd byte. Before sending back the acknowledge response, the boot
program checks for a receive error. If there was a receive error, the boot program
transmits x8H (bit 3) and returns to the command wait state again. In this case, the
upper four bits of the acknowledge response are undefined - they hold the same values
as the upper four bits of the previously issued command. When the SIO0 is configured
for I/O Interface mode, the boot program does not check for a receive error.
If the 3rd byte is equal to any of the command codes listed in Table 18-4, the boot
program echoes it back to the controller. When the Show Flash Memory Sum
command was received, the boot program echoes back a value of 30H and then
branches to the Show Flash Memory Sum routine. If the 3rd byte is not a valid
command, the boot program sends back x1H (bit 0) to the controller and returns to the
state in which it waits for a command (the third byte) again. In this case, the upper four
bits of the acknowledge response are undefined - they hold the same values as the
upper four bits of the previously issued command.
read from addresses shown below in the flash memory. Software version management
is possible by storing a software ID in these locations.
product name as shown below (where [ ] is a space) in ASCII code.
TMPM330FWFG
TMPM330FWFG
TMPM330FDFG
TMPM330FYFG
TMPM330FDFG
TMPM330FYFG
Product name
Product name
Under development
T, M, P, M, 3, 3, 0, F, D, _, [ ], _
T, M, P, M, 3, 3, 0, F, D, _, [ ], _
0x3F87_FF00 – 0x3F87_FF03
0x3F81_FF00 – 0x3F81_FF03
Page409
Code
Area
TMPM330