UPD70F3786GJ-GAE-AX Renesas Electronics America, UPD70F3786GJ-GAE-AX Datasheet - Page 1135

• Manufacturer Part Number: UPD70F3786GJ-GAE-AX
• Description: MCU 32BIT V850ES/JX3-E 144-LQFP
• Manufacturer: Renesas Electronics America
• Series: V850ES/Jx3-Er

Specifications of UPD70F3786GJ-GAE-AX

• Core Processor: RISC
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: CAN, CSI, EBI/EMI, Ethernet, I²C, UART/USART, USB
• Peripherals: DMA, LVD, PWM, WDT
• Number Of I /o: 100
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 124K x 8
• Voltage - Supply (vcc/vdd): 2.85 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

21.11 Power Saving Modes
21.11.1 CAN sleep mode
consumption. The CAN module can enter the CAN sleep mode from all operation modes. Release of the CAN sleep
mode returns the CAN module to exactly the same operation mode from which the CAN sleep mode was entered.
issued or pending.
The CAN sleep mode can be used to set the CAN controller to standby mode in order to reduce power
In the CAN sleep mode, the CAN module does not transmit messages, even when transmission requests are
(1) Entering CAN sleep mode
The CPU issues a CAN sleep mode transition request by writing 01B to the C0CTRL.PSMODE1 and
C0CTRL.PSMODE0 bits.
This transition request is only acknowledged only under the following conditions.
(i) The CAN module is already in one of the following operation modes
(ii) The CAN bus state is bus idle (the 4th bit in the interframe space is recessive)
(iii) No transmission request is pending
• Normal operation mode
• Normal operation mode with ABT
• Receive-only mode
• Single-shot mode
• Self-test mode
• CAN stop mode in all the above operation modes
Note
If any one of the conditions mentioned above is not met, the CAN module will operate as follows.
• If the CAN sleep mode is requested from the initialization mode, the CAN sleep mode transition request
• If the CAN bus state is not bus idle (i.e., the CAN bus state is either transmitting or receiving) when the
• If a request for transition to the initialization mode and a request for transition to the CAN sleep mode
• Even when the initialization mode and sleep mode are not requested simultaneously (i.e the first request
is ignored and the CAN module remains in the initialization mode.
CAN sleep mode is requested in one of the operation modes, immediate transition to the CAN sleep
mode is not possible. In this case, the CAN sleep mode transition request has to be held pending until
the CAN bus state becomes bus idle (the 4th bit in the interframe space is recessive). In the time from
the CAN sleep mode request to successful transition, the PSMODE1 and PSMODE0 bits remain 00B.
When the module has entered the CAN sleep mode, the PSMODE1 and PSMODE0 bits are set to 01B.
are made at the same time while the CAN module is in one of the operation modes, the request for the
initialization mode is enabled. The CAN module enters the initialization mode at a predetermined timing.
At this time, the CAN sleep mode request is not held pending and is ignored.
was not granted when a second request was made), the request for initialization has priority over the
CAN sleep mode request. The CAN sleep mode request is cancelled when the initialization mode is
requested. When a pending request for the initialization mode is present, a subsequent request for the
CAN sleep mode request is cancelled right at the point in time when it was submitted.
If the CAN bus is fixed to dominant, the request for transition to the CAN sleep mode is held
pending. Also the transition from CAN stop mode to CAN sleep mode is independent of the CAN
bus state.
CHAPTER 21 CAN CONTROLLER
User’s Manual U19601EJ2V0UD
Note
1133