AT91SAM9G45-EKES Atmel, AT91SAM9G45-EKES Datasheet - Page 815
AT91SAM9G45-EKES
Manufacturer Part Number
AT91SAM9G45-EKES
Description
KIT EVAL FOR AT91SAM9G45
Manufacturer
Atmel
Series
AT91SAM Smart ARMr
Type
MCUr
Datasheets
1.AT91SAM9G45-EKES.pdf
(56 pages)
2.AT91SAM9G45-EKES.pdf
(1218 pages)
3.AT91SAM9G45-EKES.pdf
(66 pages)
Specifications of AT91SAM9G45-EKES
Contents
Board
Processor To Be Evaluated
SAM9G45
Data Bus Width
32 bit
Interface Type
I2C, SPI, UART
Maximum Operating Temperature
+ 50 C
Minimum Operating Temperature
- 10 C
Operating Supply Voltage
1.8 V to 3.3 V
For Use With/related Products
AT91SAM9G45
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
Q4626953
- Current page: 815 of 1218
- Download datasheet (19Mb)
36.13.17 HSMCI Configuration Register
Name:
Addresses:
Access:
• FIFOMODE: HSMCI Internal FIFO control mode
0 = A write transfer starts when a sufficient amount of data is written into the FIFO.
When the block length is greater than or equal to 3/4 of the HSMCI internal FIFO size, then the write transfer starts as soon
as half the FIFO is filled. When the block length is greater than or equal to half the internal FIFO size, then the write transfer
starts as soon as one quarter of the FIFO is filled. In other cases, the transfer starts as soon as the total amount of data is
written in the internal FIFO.
1 = A write transfer starts as soon as one data is written into the FIFO.
• FERRCTRL: Flow Error flag reset control mode
0 = When an underflow/overflow condition flag is set, a new Write/Read command is needed to reset the flag.
1 = When an underflow/overflow condition flag is set, a read status resets the flag.
• HSMODE: High Speed Mode
0 = Default bus timing mode.
1 = If set to one, the host controller outputs command line and data lines on the rising edge of the card clock. The Host
driver shall check the high speed support in the card registers.
• LSYNC: Synchronize on the last block
0 = The pending command is sent at the end of the current data block.
1 = The pending command is sent at the end of the block transfer when the transfer length is not infinite (block count shall
be different from zero).
6438F–ATARM–21-Jun-10
31
23
15
–
–
7
–
30
22
14
HSMCI_CFG
0xFFF80054 (0), 0xFFFD0054 (1)
Read-write
–
–
6
–
29
21
13
–
–
–
5
–
FERRCTRL
LSYNC
28
20
12
–
–
4
27
19
11
–
–
–
3
–
26
18
10
–
–
–
2
–
AT91SAM9G45
25
17
–
–
9
–
1
–
FIFOMODE
HSMODE
24
16
–
–
8
0
815
Related parts for AT91SAM9G45-EKES
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
MCU ARM9 64K SRAM 144-LFBGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC ARM7 MCU FLASH 256K 100LQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC ARM9 MPU 217-LFBGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ARM9 ULTRA LOW PWR 217-LFBGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ARM9 324-TFBGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC MCU ARM9 SAMPLING 217CBGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC ARM9 MCU 217-LFBGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC ARM9 MCU 208-PQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ARM 512K HS FLASH 100-LQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ARM 512K HS FLASH 100-TFBGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC ARM9 MCU 200 MHZ 324-TFBGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC ARM MCU 16BIT 128K 256BGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC ARM7 MCU 32BIT 128K 64LQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC ARM7 MCU FLASH 256K 128-LQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC ARM7 MCU FLASH 512K 128-LQFP
Manufacturer:
Atmel
Datasheet: