AT91SAM9G45-CU Atmel, AT91SAM9G45-CU Datasheet - Page 1113

• Manufacturer Part Number: AT91SAM9G45-CU
• Description: MCU ARM9 324-TFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9G45-CU

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 400MHz
• Connectivity: EBI/EMI, Ethernet, I²C, IrDA, MMC, SPI, SSC, UART/USART, USB
• Peripherals: AC'97, DMA, I²S, LCD, POR, PWM, WDT
• Number Of I /o: 160
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: ROM
• Ram Size: 128K x 8
• Voltage - Supply (vcc/vdd): 0.9 V ~ 1.1 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 324-TFBGA
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 800 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Controller Family/series: AT91
• No. Of I/o's: 160
• Ram Memory Size: 64KB
• Cpu Speed: 400MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• For Use With: AT91SAM9G45-EKES - KIT EVAL FOR AT91SAM9G45
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

45.6.2.10
45.6.2.11
6438F–ATARM–21-Jun-10
Display
PWM
HFP
=
f
LCDDOTCK
In monochrome mode, Horizontal_display_size is equal to the number of horizontal pixels. The
number_data_lines is equal to the number of bits of the interface in single scan mode;
number_data_lines is equal to half the bits of the interface in dual scan mode.
In color mode, Horizontal_display_size equals three times the number of horizontal pixels.
In TFT Mode:
The frame rate equation is used first without considering the clock periods added at the end
beginning or at the end of each line to determine, approximately, the LCDDOTCK rate:
With this value, the CLKVAL is fixed, as well as the corresponding LCDDOTCK rate.
Then select VHDLY, HPW and HBP according to the type of LCD used and
page
Finally, the frame rate is adjusted to 70 Hz - 75 Hz with the HFP value:
The line counting is controlled by the read-only field LINECNT of LCDCON1 register. The LINE-
CNT field decreases by one unit at each falling edge of LCDHSYNC.
This block is used to configure the polarity of the data and control signals. The polarity of all
clock signals can be configured by LCDCON2[12:8] register setting.
This block also generates the lcd_pwr signal internally used to control the state of the LCD pins
and to turn on and off by software the LCD module.
It is also available on the LCDPWR pin.
This signal is controlled by the PWRCON register and respects the number of frames configured
in the GUARD_TIME field of PWRCON register (PWRCON[7:1]) between the write access to
LCD_PWR field (PWRCON[0]) and the activation/deactivation of lcd_pwr signal.
The minimum value for the GUARD_TIME field is one frame. This gives the DMA Controller
enough time to fill the FIFOs before the start of data transfer to the LCD.
This block generates the LCD contrast control signal (LCDCC) to make possible the control of
the display's contrast by software. This is an 8-bit PWM (Pulse Width Modulation) signal that can
be converted to an analog voltage with a simple passive filter.
1110.
------------------------------------------------------------------------------------------------------------- -
f
LCDVSYNC
LINEVAL
HOZVAL
LINEVAL
f
lcd_pclk
=
LINEVAL
=
=
=
HOZVAL
Horizontal_display_size 1
Vertical_display_size 1
Vertical_display_size 1
1
+
VBP
+
5
+
VFP
f
lcd_vsync
+
–
–
1
–
–
LINEVAL
VHDLY
+
+
HPW
1
AT91SAM9G45
+
HPB
+
“Equation 1” on
HOZVAL
+
1113
4