AT91SAM9G45-CU Atmel, AT91SAM9G45-CU Datasheet - Page 333

• Manufacturer Part Number: AT91SAM9G45-CU
• Description: MCU ARM9 324-TFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9G45-CU

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 400MHz
• Connectivity: EBI/EMI, Ethernet, I²C, IrDA, MMC, SPI, SSC, UART/USART, USB
• Peripherals: AC'97, DMA, I²S, LCD, POR, PWM, WDT
• Number Of I /o: 160
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: ROM
• Ram Size: 128K x 8
• Voltage - Supply (vcc/vdd): 0.9 V ~ 1.1 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 324-TFBGA
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 800 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Controller Family/series: AT91
• No. Of I/o's: 160
• Ram Memory Size: 64KB
• Cpu Speed: 400MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• For Use With: AT91SAM9G45-EKES - KIT EVAL FOR AT91SAM9G45
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

26.6
Table 26-1.
26.7
26.7.1
26.7.2
26.7.3
6438F–ATARM–21-Jun-10
Pin Name
FIQ
IRQ0 - IRQn
I/O Line Description
Product Dependencies
I/O Lines
Power Management
Interrupt Sources
I/O Line Description
The interrupt signals FIQ and IRQ0 to IRQn are normally multiplexed through the PIO control-
lers. Depending on the features of the PIO controller used in the product, the pins must be
programmed in accordance with their assigned interrupt function. This is not applicable when
the PIO controller used in the product is transparent on the input path.
Table 26-2.
The Advanced Interrupt Controller is continuously clocked. The Power Management Controller
has no effect on the Advanced Interrupt Controller behavior.
The assertion of the Advanced Interrupt Controller outputs, either nIRQ or nFIQ, wakes up the
ARM processor while it is in Idle Mode. The General Interrupt Mask feature enables the AIC to
wake up the processor without asserting the interrupt line of the processor, thus providing syn-
chronization of the processor on an event.
The Interrupt Source 0 is always located at FIQ. If the product does not feature an FIQ pin, the
Interrupt Source 0 cannot be used.
The Interrupt Source 1 is always located at System Interrupt. This is the result of the OR-wiring
of the system peripheral interrupt lines. When a system interrupt occurs, the service routine
must first distinguish the cause of the interrupt. This is performed by reading successively the
status registers of the above mentioned system peripherals.
The interrupt sources 2 to 31 can either be connected to the interrupt outputs of an embedded
user peripheral or to external interrupt lines. The external interrupt lines can be connected
directly, or through the PIO Controller.
The PIO Controllers are considered as user peripherals in the scope of interrupt handling.
Accordingly, the PIO Controller interrupt lines are connected to the Interrupt Sources 2 to 31.
The peripheral identification defined at the product level corresponds to the interrupt source
number (as well as the bit number controlling the clock of the peripheral). Consequently, to sim-
plify the description of the functional operations and the user interface, the interrupt sources are
named FIQ, SYS, and PID2 to PID31.
Instance
AIC
AIC
I/O Lines
Pin Description
Fast Interrupt
Interrupt 0 - Interrupt n
Signal
IRQ
FIQ
I/O Line
PD19
PD18
AT91SAM9G45
Type
Input
Input
Peripheral
B
B
333