AT91SAM9G45-CU Atmel, AT91SAM9G45-CU Datasheet - Page 815

• Manufacturer Part Number: AT91SAM9G45-CU
• Description: MCU ARM9 324-TFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9G45-CU

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 400MHz
• Connectivity: EBI/EMI, Ethernet, I²C, IrDA, MMC, SPI, SSC, UART/USART, USB
• Peripherals: AC'97, DMA, I²S, LCD, POR, PWM, WDT
• Number Of I /o: 160
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: ROM
• Ram Size: 128K x 8
• Voltage - Supply (vcc/vdd): 0.9 V ~ 1.1 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 324-TFBGA
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 800 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Controller Family/series: AT91
• No. Of I/o's: 160
• Ram Memory Size: 64KB
• Cpu Speed: 400MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• For Use With: AT91SAM9G45-EKES - KIT EVAL FOR AT91SAM9G45
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

36.13.17 HSMCI Configuration Register
Name:
Addresses:
Access:
• FIFOMODE: HSMCI Internal FIFO control mode
0 = A write transfer starts when a sufficient amount of data is written into the FIFO.
When the block length is greater than or equal to 3/4 of the HSMCI internal FIFO size, then the write transfer starts as soon
as half the FIFO is filled. When the block length is greater than or equal to half the internal FIFO size, then the write transfer
starts as soon as one quarter of the FIFO is filled. In other cases, the transfer starts as soon as the total amount of data is
written in the internal FIFO.
1 = A write transfer starts as soon as one data is written into the FIFO.
• FERRCTRL: Flow Error flag reset control mode
0 = When an underflow/overflow condition flag is set, a new Write/Read command is needed to reset the flag.
1 = When an underflow/overflow condition flag is set, a read status resets the flag.
• HSMODE: High Speed Mode
0 = Default bus timing mode.
1 = If set to one, the host controller outputs command line and data lines on the rising edge of the card clock. The Host
driver shall check the high speed support in the card registers.
• LSYNC: Synchronize on the last block
0 = The pending command is sent at the end of the current data block.
1 = The pending command is sent at the end of the block transfer when the transfer length is not infinite (block count shall
be different from zero).
6438F–ATARM–21-Jun-10
31
23
15
–
–
7
–
30
22
14
HSMCI_CFG
0xFFF80054 (0), 0xFFFD0054 (1)
Read-write
–
–
6
–
29
21
13
–
–
–
5
–
FERRCTRL
LSYNC
28
20
12
–
–
4
27
19
11
–
–
–
3
–
26
18
10
–
–
–
2
–
AT91SAM9G45
25
17
–
–
9
–
1
–
FIFOMODE
HSMODE
24
16
–
–
8
0
815