AT91SAM9G45-CU Atmel, AT91SAM9G45-CU Datasheet - Page 589

• Manufacturer Part Number: AT91SAM9G45-CU
• Description: MCU ARM9 324-TFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9G45-CU

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 400MHz
• Connectivity: EBI/EMI, Ethernet, I²C, IrDA, MMC, SPI, SSC, UART/USART, USB
• Peripherals: AC'97, DMA, I²S, LCD, POR, PWM, WDT
• Number Of I /o: 160
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: ROM
• Ram Size: 128K x 8
• Voltage - Supply (vcc/vdd): 0.9 V ~ 1.1 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 324-TFBGA
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 800 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Controller Family/series: AT91
• No. Of I/o's: 160
• Ram Memory Size: 64KB
• Cpu Speed: 400MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• For Use With: AT91SAM9G45-EKES - KIT EVAL FOR AT91SAM9G45
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

33.7.4.6
33.7.4.7
33.7.5
Figure 33-33. Connection to IrDA Transceivers
6438F–ATARM–21-Jun-10
IrDA Mode
Disable Successive Receive NACK
Protocol T = 1
When the USART repetition number reaches MAX_ITERATION, the ITERATION bit is set in the
Channel Status Register (US_CSR). If the repetition of the character is acknowledged by the
receiver, the repetitions are stopped and the iteration counter is cleared.
The ITERATION bit in US_CSR can be cleared by writing the Control Register with the RSIT bit
at 1.
The receiver can limit the number of successive NACKs sent back to the remote transmitter.
This is programmed by setting the bit DSNACK in the Mode Register (US_MR). The maximum
number of NACK transmitted is programmed in the MAX_ITERATION field. As soon as
MAX_ITERATION is reached, the character is considered as correct, an acknowledge is sent on
the line and the ITERATION bit in the Channel Status Register is set.
When operating in ISO7816 protocol T = 1, the transmission is similar to an asynchronous for-
mat with only one stop bit. The parity is generated when transmitting and checked when
receiving. Parity error detection sets the PARE bit in the Channel Status Register (US_CSR).
The USART features an IrDA mode supplying half-duplex point-to-point wireless communica-
tion. It embeds the modulator and demodulator which allows a glueless connection to the
infrared transceivers, as shown in
with the IrDA specification version 1.1 and support data transfer speeds ranging from 2.4 Kb/s to
115.2 Kb/s.
The USART IrDA mode is enabled by setting the USART_MODE field in the Mode Register
(US_MR) to the value 0x8. The IrDA Filter Register (US_IF) allows configuring the demodulator
filter. The USART transmitter and receiver operate in a normal asynchronous mode and all
parameters are accessible. Note that the modulator and the demodulator are activated.
The receiver and the transmitter must be enabled or disabled according to the direction of the
transmission to be managed.
To receive IrDA signals, the following needs to be done:
• Disable TX and Enable RX
Transmitter
Receiver
USART
Demodulator
Modulator
Figure
RXD
TXD
33-33. The modulator and demodulator are compliant
RX
TX
Transceivers
IrDA
AT91SAM9G45
589