LPC1767FBD100,551 NXP Semiconductors, LPC1767FBD100,551 Datasheet - Page 217

• Manufacturer Part Number: LPC1767FBD100,551
• Description: IC ARM CORTEX MCU 512K 100-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC17xxr

Specifications of LPC1767FBD100,551

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 100MHz
• Connectivity: Ethernet, I²C, IrDA, Microwire, SPI, SSI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, I²S, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 70
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 3.6 V
• Data Converters: A/D 8x12b, D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Processor Series: LPC17
• Core: ARM Cortex M3
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, MCB1760, MCB1760U, MCB1760UME
• For Use With: 622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 568-4967; 935289808551

NXP Semiconductors
11.7 Operational overview
UM10360
User manual
11.6.5 DMA engine and bus master interface
11.6.6 Register interface
11.6.7 SoftConnect
11.6.8 GoodLink
When enabled for an endpoint, the DMA Engine transfers data between RAM on the AHB
bus and the endpoint’s buffer in EP_RAM. A single DMA channel is shared between all
endpoints. When transferring data, the DMA Engine functions as a master on the AHB
bus through the bus master interface.
The Register Interface allows the CPU to control the operation of the USB Device
Controller. It also provides a way to write transmit data to the controller and read receive
data from the controller.
The connection to the USB is accomplished by bringing D+ (for a full-speed device) HIGH
through a 1.5 kOhm pull-up resistor. The SoftConnect feature can be used to allow
software to finish its initialization sequence before deciding to establish connection to the
USB. Re-initialization of the USB bus connection can also be performed without having to
unplug the cable.
To use the SoftConnect feature, the CONNECT signal should control an external switch
that connects the 1.5 kOhm resistor between D+ and +3.3V. Software can then control the
CONNECT signal by writing to the CON bit using the SIE Set Device Status command.
Good USB connection indication is provided through GoodLink technology. When the
device is successfully enumerated and configured, the LED indicator will be permanently
ON. During suspend, the LED will be OFF.
This feature provides a user-friendly indicator on the status of the USB device. It is a
useful field diagnostics tool to isolate faulty equipment.
To use the GoodLink feature the UP_LED signal should control an LED. The UP_LED
signal is controlled using the SIE Configure Device command.
Transactions on the USB bus transfer data between device endpoints and the host. The
direction of a transaction is defined with respect to the host. OUT transactions transfer
data from the host to the device. IN transactions transfer data from the device to the host.
All transactions are initiated by the host controller.
For an OUT transaction, the USB ATX receives the bi-directional D+ and D- signals of the
USB bus. The Serial Interface Engine (SIE) receives the serial data from the ATX and
converts it into a parallel data stream. The parallel data is written to the corresponding
endpoint buffer in the EP_RAM.
For IN transactions, the SIE reads the parallel data from the endpoint buffer in EP_RAM,
converts it into serial data, and transmits it onto the USB bus using the USB ATX.
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 19 August 2010
Chapter 11: LPC17xx USB device controller
UM10360
© NXP B.V. 2010. All rights reserved.
217 of 840