LPC1767FBD100,551 NXP Semiconductors, LPC1767FBD100,551 Datasheet - Page 579

• Manufacturer Part Number: LPC1767FBD100,551
• Description: IC ARM CORTEX MCU 512K 100-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC17xxr

Specifications of LPC1767FBD100,551

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 100MHz
• Connectivity: Ethernet, I²C, IrDA, Microwire, SPI, SSI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, I²S, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 70
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 3.6 V
• Data Converters: A/D 8x12b, D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Processor Series: LPC17
• Core: ARM Cortex M3
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, MCB1760, MCB1760U, MCB1760UME
• For Use With: 622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 568-4967; 935289808551

NXP Semiconductors
Table 533: A/D Status register (AD0INTEN - address 0x4003 400C) bit description
Table 534: A/D Data Registers (AD0DR0 to AD0DR7 - 0x4003 4010 to 0x4003 402C) bit description
UM10360
User manual
Bit
3
4
5
6
7
8
31:17 -
Bit
3:0
15:4
29:16
30
31
Symbol
ADINTEN3
ADINTEN4
ADINTEN5
ADINTEN6
ADINTEN7
ADGINTEN
Symbol
-
RESULT
-
OVERRUN This bit is 1 in burst mode if the results of one or more conversions was (were) lost and
DONE
29.5.4 A/D Data Registers (AD0DR0 to AD0DR7 - 0x4003 4010 to
Description
Reserved, user software should not write ones to reserved bits. The value read from a
reserved bit is not defined.
When DONE is 1, this field contains a binary fraction representing the voltage on the AD0[n]
pin, as it falls within the range of V
the input pin was less than, equal to, or close to that on V
voltage on the input was close to, equal to, or greater than that on V
Reserved, user software should not write ones to reserved bits. The value read from a
reserved bit is not defined.
overwritten before the conversion that produced the result in the RESULT bits.This bit is
cleared by reading this register.
This bit is set to 1 when an A/D conversion completes. It is cleared when this register is read. NA
Value
0
1
0
1
0
1
0
1
0
1
1
0x4003 402C)
The A/D Data Registers hold the result of the last conversion for each A/D channel, when
an A/D conversion is complete. They also include the flags that indicate when a
conversion has been completed and when a conversion overrun has occurred.
Results of ADC conversion can be read in one of two ways. One is to use the A/D Global
Data Register to read all data from the ADC. Another is to use the A/D Channel Data
Registers. It is important to use one method consistently because the DONE and
OVERRUN flags can otherwise get out of synch between the AD0GDR and the A/D
Channel Data Registers, potentially causing erroneous interrupts or DMA activity.
0
Description
Completion of a conversion on ADC channel 3 will not generate an interrupt.
Completion of a conversion on ADC channel 3 will generate an interrupt.
Completion of a conversion on ADC channel 4 will not generate an interrupt.
Completion of a conversion on ADC channel 4 will generate an interrupt.
Completion of a conversion on ADC channel 5 will not generate an interrupt.
Completion of a conversion on ADC channel 5 will generate an interrupt.
Completion of a conversion on ADC channel 6 will not generate an interrupt.
Completion of a conversion on ADC channel 6 will generate an interrupt.
Completion of a conversion on ADC channel 7 will not generate an interrupt.
Completion of a conversion on ADC channel 7 will generate an interrupt.
Only the individual ADC channels enabled by ADINTEN7:0 will generate
interrupts.
Only the global DONE flag in ADDR is enabled to generate an interrupt.
Reserved, user software should not write ones to reserved bits. The value
read from a reserved bit is not defined.
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 19 August 2010
REFP
Chapter 29: LPC17xx Analog-to-Digital Converter (ADC)
to V
REFN
. Zero in the field indicates that the voltage on
REFN
, while 0xFFF indicates that the
REFP
.
UM10360
© NXP B.V. 2010. All rights reserved.
Reset
value
0
0
0
0
0
1
NA
579 of 840
Reset
value
NA
NA
NA