LPC1767FBD100,551 NXP Semiconductors, LPC1767FBD100,551 Datasheet - Page 626

• Manufacturer Part Number: LPC1767FBD100,551
• Description: IC ARM CORTEX MCU 512K 100-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC17xxr

Specifications of LPC1767FBD100,551

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 100MHz
• Connectivity: Ethernet, I²C, IrDA, Microwire, SPI, SSI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, I²S, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 70
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 3.6 V
• Data Converters: A/D 8x12b, D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Processor Series: LPC17
• Core: ARM Cortex M3
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, MCB1760, MCB1760U, MCB1760UME
• For Use With: 622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 568-4967; 935289808551

NXP Semiconductors
UM10360
User manual
32.7.6 Prepare sector(s) for write operation <start sector number> <end
32.7.7 Copy RAM to Flash <flash address> <RAM address> <no of bytes>
sector number>
This command makes flash write/erase operation a two step process.
Table 577. ISP Prepare sector(s) for write operation command
Table 578. ISP Copy command
Command
Input
Return Code
Description
Example
Command
Input
Return Code CMD_SUCCESS |
Description
Example
"C 0 268468224 512<CR><LF>" copies 512 bytes from the RAM address
C
Flash Address(DST): Destination flash address where data bytes are to be
written. The destination address should be a 256 byte boundary.
RAM Address(SRC): Source RAM address from where data bytes are to be read.
Number of Bytes: Number of bytes to be written. Should be 256 | 512 | 1024 |
4096.
SRC_ADDR_ERROR (Address not on word boundary) |
DST_ADDR_ERROR (Address not on correct boundary) |
SRC_ADDR_NOT_MAPPED |
DST_ADDR_NOT_MAPPED |
COUNT_ERROR (Byte count is not 256 | 512 | 1024 | 4096) |
SECTOR_NOT_PREPARED_FOR WRITE_OPERATION |
BUSY |
CMD_LOCKED |
PARAM_ERROR |
CODE_READ_PROTECTION_ENABLED
This command is used to program the flash memory. The "Prepare Sector(s) for
Write Operation" command should precede this command. The affected sectors are
automatically protected again once the copy command is successfully executed.
This command is blocked when code read protection levels CRP2 or CRP3 are
enabled. When code read protection level CRP1 is enabled, individual sectors
other than sector 0 can be written.
0x1000 8000 to the flash address 0.
P
Start Sector Number
End Sector Number: Should be greater than or equal to start sector number.
CMD_SUCCESS |
BUSY |
INVALID_SECTOR |
PARAM_ERROR
This command must be executed before executing "Copy RAM to Flash" or
"Erase Sector(s)" command. Successful execution of the "Copy RAM to Flash" or
"Erase Sector(s)" command causes relevant sectors to be protected again. To
prepare a single sector use the same "Start" and "End" sector numbers.
"P 0 0<CR><LF>" prepares the flash sector 0.
All information provided in this document is subject to legal disclaimers.
Chapter 32: LPC17xx Flash memory interface and programming
Rev. 2 — 19 August 2010
UM10360
© NXP B.V. 2010. All rights reserved.
626 of 840