MPC8313ECZQADDC Freescale Semiconductor, MPC8313ECZQADDC Datasheet - Page 1055

• Manufacturer Part Number: MPC8313ECZQADDC
• Description: Microprocessors - MPU 8313 REV2.2 PB ENC EXT
• Manufacturer: Freescale Semiconductor

Specifications of MPC8313ECZQADDC

• Processor Series: MPC8313E
• Core: e300
• Data Bus Width: 16 bit
• Maximum Clock Frequency: 133 MHz
• Program Memory Size: 16 KB
• Data Ram Size: 16 KB
• Interface Type: I2C
• Mounting Style: SMD/SMT
• Package / Case: PBGA
• Number Of Programmable I/os: 32
• Number Of Timers: 4

Freescale Semiconductor
30–16 Total Bytes. This field specifies the total number of bytes to be moved with this transfer descriptor. This field is
14–12 Reserved, should be cleared. Bits reserved for future use and should be cleared.
11–10 Multiplier Override (MultO). This field can be used for transmit ISO's (that is, ISO-IN) to override the multiplier in the
31–12 Buffer Pointer. Selects the page offset in memory for the packet buffer. Non virtual memory systems will typically set
11–0
Bits
Bits
9–8
7–0
31
15
Reserved, should be cleared. Bit reserved for future use and should be cleared.
decremented by the number of bytes actually moved during the transaction and only on the successful completion of
the transaction.
The maximum value software may store in the field is 5*4K(5000H). This is the maximum number of bytes 5 page
pointers can access. Although it is possible to create a transfer up to 20K this assumes the 1st offset into the first page
is 0. When the offset cannot be predetermined, crossing past the 5th page can be guaranteed by limiting the total bytes
to 16K**. Therefore, the maximum recommended transfer is 16K(4000H).
If the value of the field is zero when the host controller fetches this transfer descriptor (and the active bit is set), the
device controller executes a zero-length transaction and retires the transfer descriptor.
It is not a requirement for IN transfers that Total Bytes To Transfer be an even multiple of Maximum Packet Length. If
software builds such a transfer descriptor for an IN transfer, the last transaction will always be less that Maximum
Packet Length.
Interrupt On Complete (IOC). This bit is used to indicate if USBINT is to be set in response to device controller being
finished with this dTD.
QH. This field must be zero for all packet types that are not transmit-ISO.
Example:
Three packets are sent: {Data2(8); Data1(7); Data0(0)}
Two packets are sent: {Data1(8); Data0(7)}
For maximal efficiency, software should compute MultO = greatest integer of (Total Bytes/Max. Packet Size) except for
the case when Total bytes = 0; then MultO should be 1.
Note: Non-ISO and non-TX endpoints must set MultO = 00.
Reserved, should be cleared. Bits reserved for future use and should be cleared.
Status. This field is used by the Device Controller to communicate individual command execution states back to the
Device Controller software. This field contains the status of the last transaction performed on this qTD. The bit
encodings are:
Bit
7
6
5
3
4,2,0
the buffer pointers to a series of incrementing integers.
Current Offset. Offset into the 4kb buffer where the packet is to begin.
if QH.multiplier = 3; Maximum packet size = 8; Total bytes = 15; MultiO = 0 [default]
if QH.multiplier = 3; Maximum packet size = 8; Total bytes = 15; MultiO = 2
MPC8313E PowerQUICC™ II Pro Integrated Processor Family Reference Manual, Rev. 2
Status Field Description
Active
Halted
Data Buffer Error
Transaction Error
Reserved, should be cleared
Table 16-80. Buffer Pointer Page 0
Table 16-79. dTD Token
Description
Description
Universal Serial Bus Interface
16-127