MMC2114CFCAG33 Freescale Semiconductor, MMC2114CFCAG33 Datasheet - Page 237

• Manufacturer Part Number: MMC2114CFCAG33
• Description: IC MCU 32BIT 33MHZ 144-LQFP
• Manufacturer: Freescale Semiconductor
• Series: MCorer

Specifications of MMC2114CFCAG33

• Core Processor: M210
• Core Size: 32-Bit
• Speed: 33MHz
• Connectivity: EBI/EMI, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 67
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• Processor Series: MMC2114
• Core: M-CORE
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: SCI/SPI
• Maximum Clock Frequency: 33 MHz
• Number Of Programmable I/os: 104
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Controller Family/series: MCORE
• No. Of I/o's: 104
• Ram Memory Size: 32KB
• Cpu Speed: 33MHz
• No. Of Timers: 2
• Embedded Interface Type: SCI, SPI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

10.8.4 Stop Mode
MMC2114 • MMC2113 • MMC2112 — Rev. 1.0
MOTOROLA
WARNING:
NOTE:
The PVIOL flag will be set during a command write sequence after the
word write to the SGFM array if any of the illegal operations below are
performed. Such operations will cause the command sequence to
immediately abort.
If a FLASH physical block is read during a program or erase operation
on that block (SGFMUSTAT bit CCIF = 0), the read will return non-valid
data and the ACCERR flag will not be set.
If a command is active (CCIF = 0) when the MCU enters stop mode, the
command sequence monitor will perform the following:
The state of any word(s) being programmed or any erase pages/physical
blocks being erased is not guaranteed if the MCU enters stop mode with
a command in progress.
Active commands are immediately aborted when the MCU enters
stop mode. Do not execute the STOP instruction during program
and erase operations.
1. Writing to an address in a protected area of the SGFM array.
2. Writing a mass erase command to SGFMCMD while any logical
1. The command in progress will be aborted.
2. The FLASH high voltage circuitry will be switched off and any
3. The CCIF and ACCERR flags will be set if a command is active
Freescale Semiconductor, Inc.
Second Generation FLASH for M•CORE (SGFM)
For More Information On This Product,
sector is protected (see
pending command (CBEIF = 0) will not be executed when the
MCU exits stop mode.
when the MCU enters stop mode.
Go to: www.freescale.com
Second Generation FLASH for M•CORE (SGFM)
10.7.2.1 SGFM Protection
Advance Information
SGFM User Mode
Register).
237