EFM32G200F16 Energy Micro, EFM32G200F16 Datasheet - Page 176

• Manufacturer Part Number: EFM32G200F16
• Description: MCU 32BIT 16KB FLASH 32-QFN
• Manufacturer: Energy Micro
• Series: Geckor

Specifications of EFM32G200F16

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 32MHz
• Connectivity: EBI/EMI, I²C, IrDA, SmartCard, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.8 V
• Data Converters: A/D 4x12b, D/A 1x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad
• Processor Series: EFM32G200
• Core: ARM Cortex-M3
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, UART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 2
• Operating Supply Voltage: 1.8 V to 3.8 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

16.3 Functional Description
16.3.1 Modes of Operation
2010-09-06 - d0001_Rev1.00
• Configurable number of data bits, 4-16 (plus the parity bit, if enabled)
• Configurable number of stop bits in asynchronous mode: 0.5, 1, 1.5, 2
• HW collision detection
• Multi-processor mode
• IrDA modulator on USART0
• SmartCard (ISO7816) mode
• Separate interrupt vectors for receive and transmit interrupts
• Loopback mode
An overview of the USART module is shown in Figure 16.1 (p. 176) .
Figure 16.1. USART Overview
The USART operates in either asynchronous or synchronous mode.
In synchronous mode, a separate clock signal is transmitted with the data. This clock signal is generated
by the bus master, and both the master and slave sample and transmit data according to this clock.
Both master and slave modes are supported by the USART. The synchronous communication mode is
compatible with the Serial Peripheral Interface Bus (SPI) standard.
In asynchronous mode, no separate clock signal is transmitted with the data on the bus. The USART
receiver thus has to determine where to sample the data on the bus from the actual data. To make this
possible, additional synchronization bits are added to the data when operating in asynchronous mode,
resulting in a slight overhead.
• HW parity bit generation and check
• Half duplex communication
• Communication debugging
U(S)n_RX
U(S)n_TX
USn_CLK
USn_CS
Pin
ctrl
UART Control
and status
m odulator
IrDA
dem odulator
...the world's most energy friendly microcontrollers
TX Shift Register
Peripheral Bus
IrDA
176
(2-level FIFO)
TX Buffer
Baud rate
generator
RX Shift Register
(2-level FIFO)
RX Buffer
www.energymicro.com
! RXBLOCK