EFM32G200F16 Energy Micro, EFM32G200F16 Datasheet - Page 254

• Manufacturer Part Number: EFM32G200F16
• Description: MCU 32BIT 16KB FLASH 32-QFN
• Manufacturer: Energy Micro
• Series: Geckor

Specifications of EFM32G200F16

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 32MHz
• Connectivity: EBI/EMI, I²C, IrDA, SmartCard, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.8 V
• Data Converters: A/D 4x12b, D/A 1x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad
• Processor Series: EFM32G200
• Core: ARM Cortex-M3
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, UART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 2
• Operating Supply Voltage: 1.8 V to 3.8 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

2010-09-06 - d0001_Rev1.00
complementary outputs connected to the respective low-side transistors (UL, VL, WL shown in
Figure 19.21 (p. 254) ). Transistors used in such a bridge often do not open/close instantaneously, and
using the exact complementary inputs for the high and low side of a half-bridge may result in situations
where both gates are open. This can give unnecessary current-draw and short circuit the power supply.
The DTI unit provides dead-time insertion to deal with this problem.
Figure 19.21. TIMER Triple Half-Bridge
For each of the 3 compare-match outputs of TIMER0, an additional complementary output is provided by
the DTI unit. These outputs, named TIM0_CDTI0, TIM0_CDTI1 and TIM0_CDTI2 are provided to make
control of e.g. 3-channel BLDC or PMAC motors possible using only a single timer, see Figure 19.22 (p.
254) .
Figure 19.22. TIMER Overview of Dead-Time Insertion Block for a Single PWM channel
The DTI unit is enabled by setting DTEN in TIMER0_DTCTRL. In addition to providing the
complementary outputs, the DTI unit then also overrides the compare match outputs from the timer.
The DTI unit gives the rising edges of the PWM outputs and the rising edges of the complementary
PWM outputs a configurable time delay. By doing this, the DTI unit introduces a dead-time where both
the primary and complementary outputs in a pair are inactive as seen in Figure 19.23 (p. 254) .
Figure 19.23. TIMER Polarity of Both Signals are Set as Active-High
Original PWM (TIM0_CCx_pre)
UH
UL
Original PWM
TIM0_CDTI0
TIM0_CC0
HFPERCLK
VH
VL
TIMERn
WH
WL
W
Clock control
V
U
DTFALLT
dt1
...the world's most energy friendly microcontrollers
254
Counter
Select
= 0
DTRISET
dt2
Prim ary output (TIM0_CCx)
Com plem entary Output (TIM0_CDTIx)
www.energymicro.com