EFM32G200F16 Energy Micro, EFM32G200F16 Datasheet - Page 43

• Manufacturer Part Number: EFM32G200F16
• Description: MCU 32BIT 16KB FLASH 32-QFN
• Manufacturer: Energy Micro
• Series: Geckor

Specifications of EFM32G200F16

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 32MHz
• Connectivity: EBI/EMI, I²C, IrDA, SmartCard, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.8 V
• Data Converters: A/D 4x12b, D/A 1x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad
• Processor Series: EFM32G200
• Core: ARM Cortex-M3
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, UART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 2
• Operating Supply Voltage: 1.8 V to 3.8 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

8.4.2.3.1 Invalid
8.4.2.3.2 Basic
8.4.2.3.3 Auto-request
8.4.2.3.4 Ping-pong
2010-09-06 - d0001_Rev1.00
Note
For all cycle types, the controller arbitrates after 2
a large 2
DMA transfer completes. Therefore, you must take care when setting the R_power, that you do not
significantly increase the latency for high-priority channels.
After the controller completes a DMA cycle it sets the cycle type to invalid, to prevent it from repeating
the same DMA cycle.
In this mode, you configure the controller to use either the primary, or alternate, data structure. After you
enable the channel, and the controller receives a request then the flow for this DMA cycle is:
1. The controller performs 2
2. The controller arbitrates:
3. The controller sets dma_done[C] HIGH for one HFCORECLK cycle. This indicates to the host
When the controller operates in this mode, it is only necessary for it to receive a single request to enable
it to complete the entire DMA cycle. This enables a large data transfer to occur, without significantly
increasing the latency for servicing higher priority requests, or requiring multiple requests from the
processor or peripheral.
You can configure the controller to use the primary, or alternate, data structure. After you enable the
channel, and the controller receives a request for this channel, then the flow for this DMA cycle is:
1. The controller performs 2
2. The controller arbitrates. When channel C has the highest priority then the DMA cycle continues at
3. The controller sets dma_done[C] HIGH for one HFCORECLK cycle. This indicates to the host
In ping-pong mode, the controller performs a DMA cycle using one of the data structures and it then
performs a DMA cycle using the other data structure. The controller continues to switch from primary to
cycle_ctrl
b010
b011
b100
b101
b110
b111
at step 3 (p. 43) .
• if a higher-priority channel is requesting service then the controller services that channel
• if the peripheral or software signals a request to the controller then it continues at step 1 (p. 43) .
processor that the DMA cycle is complete.
flow continues at step 3 (p. 43) .
step 1 (p. 43) .
processor that the DMA cycle is complete.
R
The cycle_ctrl bits are located in the channel_cfg memory location that Section 8.4.3.3 (p.
53) describes.
value then it prevents all other channels from performing a DMA transfer, until the low-priority
Description
Auto-request
Ping-pong
Memory scatter-gather using the primary data structure
Memory scatter-gather using the alternate data structure
Peripheral scatter-gather using the primary data structure
Peripheral scatter-gather using the alternate data structure
R
R
transfers. If the number of transfers remaining is zero the flow continues
transfers for channel C. If the number of transfers remaining is zero the
...the world's most energy friendly microcontrollers
43
R
DMA transfers. If you set a low-priority channel with
www.energymicro.com