PIC18F97J60-I/PF Microchip Technology, PIC18F97J60-I/PF Datasheet - Page 198

• Manufacturer Part Number: PIC18F97J60-I/PF
• Description: IC PIC MCU FLASH 65KX16 100TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F97J60-I/PF

• Program Memory Type: FLASH
• Program Memory Size: 128KB (64K x 16)
• Package / Case: 100-TQFP, 100-VQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 41.667MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 70
• Ram Size: 3808 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3808 B
• Interface Type: Display Driver/Ethernet/EUSART/I2C/MSSP/SPI
• Maximum Clock Frequency: 41.667 MHz
• Number Of Programmable I/os: 70
• Number Of Timers: 5
• Operating Supply Voltage: 2.35 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136, DM183033
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• Package: 100TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 41.667 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162064 - HEADER INTFC MPLABICD2 64/80/100DM163024 - BOARD DEMO PICDEM.NET 2
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F97J60 FAMILY
17.4.4
In the Half-Bridge Output mode, two pins are used as
outputs to drive push-pull loads. The PWM output
signal is output on the P1A pin, while the complemen-
tary PWM output signal is output on the P1B pin
(Figure 17-4). This mode can be used for half-bridge
applications, as shown in Figure 17-5, or for full-bridge
applications, where four power switches are being
modulated with two PWM signals.
In Half-Bridge Output mode, the programmable
dead-band delay can be used to prevent shoot-through
current in half-bridge power devices. The value of bits,
P1DC6:P1DC0, sets the number of instruction cycles
before the output is driven active. If the value is greater
than the duty cycle, the corresponding output remains
inactive during the entire cycle. See Section 17.4.6
“Programmable Dead-Band Delay” for more details
on dead-band delay operations.
Since the P1A and P1B outputs are multiplexed with
the PORTC<2> and PORTE<6> data latches, the
TRISC<2> and TRISE<6> bits must be cleared to
configure P1A and P1B as outputs.
FIGURE 17-5:
DS39762B-page 196
Standard Half-Bridge Circuit (“Push-Pull”)
Half-Bridge Output Driving a Full-Bridge Circuit
HALF-BRIDGE MODE
EXAMPLES OF HALF-BRIDGE OUTPUT MODE APPLICATIONS
PIC18F97J60
P1A
P1B
PIC18F97J60
P1A
P1B
FET
Driver
FET
Driver
Preliminary
FET
Driver
FET
Driver
FIGURE 17-4:
Note 1: At this time, the TMR2 register is equal to the
P1A
P1B
td = Dead Band Delay
(2)
(2)
2: Output signals are shown as active-high.
Load
(1)
V+
V-
PR2 register.
V+
V-
td
Duty Cycle
Period
Load
td
HALF-BRIDGE PWM
OUTPUT
© 2006 Microchip Technology Inc.
FET
Driver
FET
Driver
(1)
+
V
-
+
V
-
Period
(1)