SAM9263 Atmel Corporation, SAM9263 Datasheet - Page 1026

• Manufacturer Part Number: SAM9263
• Manufacturer: Atmel Corporation

Specifications of SAM9263

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 240 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Can: 1
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: Yes
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 96
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

Table 47-2.
Note:
47.3
47.3.1
1026
Symbol
V
R
I
I
O
SC
OH
PULLUP
1. Even during startup V
Power Consumption
AT91SAM9263
Power Consumption versus Modes
Parameter
Output High-level
Voltage
Pull-up Resistance
Output Current
Static Current
DC Characteristics (Continued)
The values in
sumption with operating conditions as follows:
Figure 47-1. Measures Schematics
These figures represent the power consumption measured on the power supplies.
• Power consumption of power supply in four different modes: Full Speed (PCK and MCK
• Power consumption by peripheral: calculated as the difference in current measurement after
• V
• V
• There is no consumption on the I/Os of the device
• All peripheral clocks are deactivated
present), Idle (only MCK present), Quasi Static (the system is running at 500 Hz), Backup (in
Shutdown Mode)
having enabled then disabled the corresponding clock.
VDDIOP
DDIOM0
DDPLL
Conditions
I
CMOS (I
TTL (I
PA0-PA31, PB0-PB31, PC0-PC31, PD0-PD31, PE0-
PE31
PA0-PA31, PB0-PB31, PC0-PC31,
PD0-PD31, PE0-PE31
On V
All inputs driven TMS, TDI, TCK,
NRST = 1
On V
consumption
All inputs driven WKUP = 0
O
= V
must always be superior or equal to V
Max, V
= V
VDDCORE
VDDBU
DDOSC
O
Table 47-3
DDIOM1
Max) V
O
VDDIO
<0.3 mA) V
= 1.2V, Logic cells
= 3.3V
= 1.2V, MCK = 0 Hz
= V
VDDIO
from 3.0V to 3.6V
DDIOP0
and
from 1.65V to 1.95V
VDDIO
Table 47-4 on page 1029
= V
from 1.65V to 1.95V
DDIOP1
AMP1
AMP2
= 3.3 V
VDDCORE
T
T
T
T
A
A
A
A
=25°C
=85°C
=25°C
=85°C
VDDCORE
.
VDDBU
are estimated values of the power con-
V
V
V
VDDIO
VDDIO
VDDIO
Min
70
- 0.4
- 0.1
- 0.4
Typ
100
240
3
6249I–ATARM–3-Oct-11
3500
Max
175
17
8
kOhm
Units
mA
µA
µA
V
V
V