SAM9263 Atmel Corporation, SAM9263 Datasheet - Page 157

• Manufacturer Part Number: SAM9263
• Manufacturer: Atmel Corporation

Specifications of SAM9263

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 240 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Can: 1
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: Yes
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 96
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

20.5.2
Register Name:MATRIX_SCFG0...MATRIX_SCFG6
Address:
Access Type:Read-write
• SLOT_CYCLE: Maximum Number of Allowed Cycles for a Burst
When the SLOT_CYCLE limit is reached for a burst, it may be broken by another master trying to access this slave.
This limit has been placed to avoid locking a very slow slave when very long bursts are used.
Note that an unreasonably small value breaks every burst and the Bus Matrix then arbitrates without performing any data
transfer. 16 cycles is a reasonable value for SLOT_CYCLE.
• DEFMASTR_TYPE: Default Master Type
0: No Default Master
At the end of current slave access, if no other master request is pending, the slave is disconnected from all masters.
This results in a one-cycle latency for the first access of a burst transfer or for a single access.
1: Last Default Master
At the end of current slave access, if no other master request is pending, the slave remains connected to the last master
that accessed it.
This results in not having the one cycle latency when the last master tries access to the slave again.
2: Fixed Default Master
At the end of the current slave access, if no other master request is pending, the slave connects to the fixed master the
number of which has been written in the FIXED_DEFMSTR field.
This results in not having the one cycle latency when the fixed master tries access to the slave again.
• FIXED_DEFMSTR: Fixed Default Master
This is the number of the Default Master for this slave. Only used if DEFMASTR_TYPE is 2. Specifying the number of a
master which is not connected to the selected slave is equivalent to setting DEFMASTR_TYPE to 0.
• ARBT: Arbitration Type
0: Round-Robin Arbitration
1: Fixed Priority Arbitration
2: Reserved
3: Reserved
6249I–ATARM–3-Oct-11
31
23
15
–
–
–
7
Bus Matrix Slave Configuration Registers
0xFFFFEC40
30
22
14
–
–
6
29
21
13
–
–
5
28
20
12
–
–
4
FIXED_DEFMSTR
SLOT_CYCLE
27
19
11
–
–
3
26
18
10
–
–
2
AT91SAM9263
25
17
9
–
1
DEFMSTR_TYPE
ARBT
24
16
8
–
0
157