SAM9263 Atmel Corporation, SAM9263 Datasheet - Page 311

• Manufacturer Part Number: SAM9263
• Manufacturer: Atmel Corporation

Specifications of SAM9263

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 240 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Can: 1
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: Yes
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 96
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

25.4.7
Name: DMAC_CFGxH
Addresses:0x00800044 [0], 0x0080009C [1]
Access: Read-write
Reset: 0x0
• FCMODE: Flow Control Mode
Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller.
0 = Source transaction requests are serviced when they occur. Data pre-fetching is enabled.
1 = Source transaction requests are not serviced until a destination transaction request occurs. In this mode the amount of
data transferred from the source is limited such that it is guaranteed to be transferred to the destination prior to block termi-
nation by the destination. Data pre-fetching is disabled.
• FIFO_MODE: R/W 0x0 FIFO Mode Select
Determines how much space or data needs to be available in the FIFO before a burst transaction request is serviced.
0 = Space/data available for single AMBA transfer of the specified transfer width.
1 = Space/data available is greater than or equal to half the FIFO depth for destination transfers and less than half the FIFO
depth for source transfers. The exceptions are at the end of a burst transaction request or at the end of a block transfer.
• PROTCTL: Protection Control
bits used to drive the AMBA HPROT[3:1] bus. The AMBA Specification recommends that the default value of HPROT indi-
cates a non-cached, nonbuffered, privileged data access. The reset value is used to indicate such an access.
• HPROT[0] is tied high as all transfers are data accesses as there are no opcode fetches. There is a one-to-one mapping
Assigns a hardware handshaking interface (0 - DMAH_NUM_HS_INT-1) to the source of channel x if the
DMAC_CFGx.HS_SEL_SRC field is 0. Otherwise, this field is ignored. The channel can then communicate with the source
peripheral connected to that interface via the assigned hardware handshaking interface.
For correct DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking
interface.
• DEST_PER: Destination Hardware Handshaking Interface
Assigns a hardware handshaking interface (0 - DMAH_NUM_HS_INT-1) to the destination of channel x if the
DMAC_CFGx.HS_SEL_DST field is 0. Otherwise, this field is ignored. The channel can then communicate with the desti-
nation peripheral connected to that interface via the assigned hardware handshaking interface.
For correct DMA operation, only one peripheral (source or destination) should be assigned to the same handshaking
interface.
6249I–ATARM–3-Oct-11
of these register bits to the HPROT[3:1] master interface signals. SRC_PER: Source Hardware Handshaking
Interface
SRC_PER
31
23
15
–
–
–
7
Configuration Register for Channel x High
30
22
14
–
–
6
–
29
21
13
–
–
5
–
DEST_PER
28
20
12
–
–
4
PROTCTL
27
19
11
–
–
3
26
18
10
–
–
2
FIFO_MODE
AT91SAM9263
SRC_PER
25
17
–
–
9
1
FCMODE
24
16
–
–
8
0
311