SAM9263 Atmel Corporation, SAM9263 Datasheet - Page 1089

• Manufacturer Part Number: SAM9263
• Manufacturer: Atmel Corporation

Specifications of SAM9263

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 240 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Can: 1
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: Yes
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 96
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

6249I–ATARM–3-Oct-11
Revision
6249F
Revision
6249E
Comments
Section 5.1 ”Power
Section 5.2, “Power Sequence Requirements removed from datasheet.
USART:
Section 34.5.1 ”I/O
Section 34.3 ”Application Block
Comments
Overview:
New Ordering Code: AT91SAM9263B-CU added to
Section 8.1.2.1 ”BMS = 1, Boot on Embedded
memory”.
Section 5.2 ”Power Sequence
Section 10.4.3
Section 10.5.8 ”Multimedia Card
Table 3-1, ”Signal Description
Table 10-6, ”Multiplexing on PIO Controller
New!!! Address Offsets added to all register tables in User Interface sections of the datasheet.
AIC:
“AIC Spurious Interrupt Vector Register” on page 398
Section 29.6.3 ”Interrupt
Section 29.7.5 ”Protect
updated.
Boot Program:
Section 13.1
Section 13.6 ”NAND Flash
Section 13.6.1 ”Supported NAND Flash
Section 13.3 ”Device
CAN:
Section 37.6.4.6 “Error Interrupt Handler” on page
”Overview”, 3rd and 4th paragraphs updated.
”EBI1”, System Resource Multiplexing, Ethernet 10/100 MAC limitation on EBI1 updated.
Lines”, reference to modem mode removed.
Supplies”, VDDCORE and VDDBU updated.
Initialization”, additional supported crystals added in
Mode”, “writing PROT enables Debug Control Protect Mode in AIC_DCR register,
Sources”, Interrupt Source 1 OR-wiring description updated.
Boot”, 1st and 2nd paragraphs removed, 3rd paragraph updated.
List”, Image Sensor Interface, ISI_MCK is provided by PCK3.
Requirements”, section added to datasheet.
Diagram”, updated and modem removed
Interface”, protocol specification compatibilities updated.
Devices”, must be connected on EBI0.
E”, ISI_MCK removed from PE11 line of the table.
ROM”, changes to list under “Bootloader on a non-volatile
661, section added to datasheet.
Table 49-1, ”AT91SAM9263 Ordering
fixed typo in bitfield.
Table
13-1.
AT91SAM9263
Information”.
Change
Request
Ref.
5791/5793
5743
Change
Request
Ref.
5560
5425
5643
5713
5282
5329
rfo
4749:
5191
5193
5244
5266
5280
4736
1089