SAM9263 Atmel Corporation, SAM9263 Datasheet - Page 193

• Manufacturer Part Number: SAM9263
• Manufacturer: Atmel Corporation

Specifications of SAM9263

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 240 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Can: 1
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: Yes
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 96
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

23.3.1.2
Table 23-5.
Table 23-6.
Table 23-7.
Notes:
23.4
23.4.1
6249I–ATARM–3-Oct-11
27
27
27
26
26
26
Bk[1:0]
1. M0 is the byte address inside a 16-bit half-word.
4. Bk[1] = BA1, Bk[0] = BA0.
Product Dependencies
25
25
25
SDRAM Device Initialization
Bk[1:0]
Bk[1:0]
16-bit Memory Data Bus Width
24
24
24
SDRAM Configuration Mapping: 2K Rows, 256/512/1024/2048 Columns
SDRAM Configuration Mapping: 4K Rows, 256/512/1024/2048 Columns
SDRAM Configuration Mapping: 8K Rows, 256/512/1024/2048 Columns
Bk[1:0]
Bk[1:0]
Bk[1:0]
23
23
23
Bk[1:0]
Bk[1:0]
Bk[1:0]
22
22
22
Bk[1:0]
Bk[1:0]
The initialization sequence is generated by software. The SDRAM devices are initialized by the
following sequence:
21
21
21
Bk[1:0]
1. SDRAM features must be set in the configuration register: asynchronous timings (TRC,
2. For mobile SDRAM, temperature-compensated self refresh (TCSR), drive strength
3. The SDRAM memory type must be set in the Memory Device Register.
4. A minimum pause of 200 µs is provided to precede any signal toggle.
5.
20
20
20
TRAS, etc.), number of columns, rows, CAS latency, and the data bus width.
(DS) and partial array self refresh (PASR) must be set in the Low Power Register.
(1)
1 in the Mode Register and perform a write access to any SDRAM address.
A NOP command is issued to the SDRAM devices. The application must set Mode to
19
19
19
Row[12:0]
Row[11:0]
18
18
18
Row[10:0]
Row[12:0]
Row[11:0]
17
17
17
Row[10:0]
Row[12:0]
Row[11:0]
16
16
16
Row[10:0]
Row[12:0]
Row[11:0]
15
15
15
CPU Address Line
CPU Address Line
CPU Address Line
Row[10:0]
14
14
14
13
13
13
12
12
12
11
11
11
10
10
10
9
9
9
8
8
8
7
7
7
Column[10:0]
Column[10:0]
Column[10:0]
Column[9:0]
Column[9:0]
Column[9:0]
6
6
6
Column[8:0]
Column[8:0]
Column[8:0]
AT91SAM9263
Column[7:0]
Column[7:0]
Column[7:0]
5
5
5
4
4
4
3
3
3
2
2
2
1
1
1
M0
M0
M0
M0
M0
M0
M0
M0
M0
M0
M0
M0
235
0
0
0