DF2170BVTE33V Renesas Electronics America, DF2170BVTE33V Datasheet - Page 349

IC H8S/2170 MCU FLASH 100-TQFP

DF2170BVTE33V

Manufacturer Part Number
DF2170BVTE33V
Description
IC H8S/2170 MCU FLASH 100-TQFP
Manufacturer
Renesas Electronics America
Series
H8® H8S/2100r
Datasheet

Specifications of DF2170BVTE33V

Core Processor
H8S/2000
Core Size
16-Bit
Speed
33MHz
Connectivity
SCI, USB
Peripherals
DMA, POR, PWM, WDT
Number Of I /o
76
Program Memory Size
256KB (256K x 8)
Program Memory Type
FLASH
Ram Size
32K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Oscillator Type
External
Operating Temperature
-20°C ~ 75°C
Package / Case
100-TQFP, 100-VQFP
For Use With
HS0005KCU11H - EMULATOR E10A-USB H8S(X),SH2(A)3DK2166 - DEV EVAL KIT H8S/2166
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Data Converters
-

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
DF2170BVTE33V
Manufacturer:
Renesas Electronics America
Quantity:
10 000
11.6
11.6.1
SCI operation can be disabled or enabled using the module stop control register. The initial setting
is for SCI operation to be halted. Register access is enabled by clearing module stop mode. For
details, refer to section 16, Power-Down Modes.
11.6.2
The TDRE flag in SSR is a status flag that indicates that transmit data has been transferred from
TDR to TSR. When the SCI transfers data from TDR to TSR, the TDRE flag is set to 1.
Data can be written to TDR regardless of the state of the TDRE flag. However, if new data is
written to TDR when the TDRE flag is cleared to 0, the data stored in TDR will be lost since it has
not yet been transferred to TSR. It is therefore essential to check that the TDRE flag is set to 1
before writing transmit data to TDR.
11.6.3
• Transmission
• Reception
Operation should be stopped (by clearing TE, TIE, and TEIE to 0) before making a module
stop mode or software standby mode transition. TSR, TDR, and SSR are reset. The output pin
states in module stop mode or software standby mode depend on the port settings, and become
high-level output after the relevant mode is cleared. If a transition is made during transmission,
the data being transmitted will be undefined.
When transmitting without changing the transmit mode after the relevant mode is cleared,
transmission can be started by setting TE to 1 again, and performing the following sequence:
SSR read → TDR write → TDRE clearance. To transmit with a different transmit mode after
clearing the relevant mode, the procedure must be started again from initialization.
Figure 11.9 shows a sample flowchart for mode transition during transmission.
Receive operation should be stopped (by clearing RE to 0) before making a module stop mode
or software standby mode transition. RSR, RDR, and SSR are reset. If a transition is made
during reception, the data being received will be invalid.
To continue receiving without changing the reception mode after the relevant mode is cleared,
set RE to 1 before starting reception. To receive with a different receive mode, the procedure
must be started again from initialization.
Figure 11.10 shows a sample flowchart for mode transition during reception.
Usage Notes
Module Stop Mode Setting
Relation between Writes to TDR and the TDRE Flag
Operation in Case of Mode Transition
Rev. 2.00, 03/04, page 315 of 534

Related parts for DF2170BVTE33V