TMP89xy60UG/FG Toshiba, TMP89xy60UG/FG Datasheet - Page 344

no-image

TMP89xy60UG/FG

Manufacturer Part Number
TMP89xy60UG/FG
Description
Manufacturer
Toshiba
Datasheet

Specifications of TMP89xy60UG/FG

Package
LQFP64/QFP64
Rom Types (m=mask,p=otp,f=flash)
M/F
Rom Size
32/60
Ram Size
3K
Driver Led
8
Driver Lcd
-
Spi/sio Channels
-
Uart/sio Channels
2
I2c/sio Channels
1
High-speed Serial Output
-
Adc 8-bit Channels
-
Adc 10-bit Channels
16
Da Converter Channels
-
Timer Counter 18-bit Channel
-
Timer Counter 16-bit Channel
2
Timer Counter 8-bit Channel
4
Motor Channels
-
Watchdog Timer
Y
Dual Clock
Y
Clock Gear
Y
Number Of I/o Ports
58
Power Supply (v)
4.3 to 5.5
21.3
Command Sequence
RA006
21.3.2
by the upper 4 bits of the 6th bus write cycle address. The range of addresses that can be specified is shown in
Table 21-3. For example, to erase 4 kbytes from 0x1000 through 0x1FFF in the code area, set FLSCR1<FAREA>
to "0y11", set "0xD5" on FLSCR2<CR1EN>, and then specify either 0x9000 or 0x9FFF as the 6th bus write
cycle. The sector erase command is effective only in MCU and serial PROM modes, and it cannot be used in
parallel PROM mode.
ongoing erase operation is not completed. To check the completion of the erase operation, perform read operations
twice on the same address in the flash memory, and perform polling until the same data is read from the flash
memory. During the erase operation, bit 6 is reversed each time a read is performed.
Note 1: The data and code areas become mirror areas. As you access these areas, you are brought to the same
Note 2: Do not perform a sector erase on areas other than those shown in Table 21-3.
This command erases the flash memory in units of 4 kbytes. The flash memory area to be erased is specified
The time needed to erase 4 kbytes is 30 ms maximum. The next command sequence cannot be executed if an
Data in the erased area is 0xFF.
Sector erase (4-kbyte partial erase)
Table 21-3 Range of Addresses Specifiable
Table 21-2 Range of Addresses Specifiable (BA)
physical address in memory. When performing a sector erase, make sure that you erase data from either of
these two areas, not both.
(Data area)
(Data area)
(Code area)
(Code area)
(Data area)
(Data area)
AREA D0
AREA D1
AREA D0
AREA D1
AREA C0
AREA C1
Erase Area
Write Area
0xC000 through 0xCFFF
0xD000 through 0xDFFF
0xA000 through 0xAFFF
0xB000 through 0xBFFF
0xE000 through 0xEFFF
0x1000 through 0x7FFF
0x8000 through 0xFFFF
0x1000 through 0x7FFF
0x8000 through 0xFFFF
0x1000 through 0x1FFF
0x2000 through 0x2FFF
0x3000 through 0x3FFF
0x4000 through 0x4FFF
0x5000 through 0x5FFF
0x6000 through 0x6FFF
0x7000 through 0x7FFF
0x8000 through 0x8FFF
0x9000 through 0x9FFF
0xF000 through 0xFFFF
Page 328
<FAREA>
FLSCR1
<FAREA>
FLSCR1
01
00
11
10
01
00
Address specified by instruction
(Address of 4th bus write cycle)
Address specified by instruction
(Address of 6th bus write cycle)
0x9000 through 0xFFFF
0x8000 through 0xFFFF
0x9000 through 0xFFFF
0x8000 through 0xFFFF
0xC000 through 0xCFFF
0xD000 through 0xDFFF
0xC000 through 0xCFFF
0xD000 through 0xDFFF
0xA000 through 0xAFFF
0xB000 through 0xBFFF
0xE000 through 0xEFFF
0xA000 through 0xAFFF
0xB000 through 0xBFFF
0xE000 through 0xEFFF
0x9000 through 0x9FFF
0xF000 through 0xFFFF
0x8000 through 0x8FFF
0x9000 through 0x9FFF
0xF000 through 0xFFFF
TMP89FS60

Related parts for TMP89xy60UG/FG