DF2110BVTE10 Renesas Electronics America, DF2110BVTE10 Datasheet - Page 190

• Manufacturer Part Number: DF2110BVTE10
• Description: MCU 3V 64K 100-TQFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2100r

Specifications of DF2110BVTE10

• Core Processor: H8S/2000
• Core Size: 16-Bit
• Speed: 10MHz
• Connectivity: Host Interface (LPC), I²C, SCI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 82
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 100-TQFP, 100-VQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Data Converters: -
• Other names: HD64F2110BVTE10; HD64F2110BVTE10

Section 9 16-Bit Free-Running Timer (FRT)
9.3.1
FRC is a 16-bit readable/writable up-counter. The clock source is selected by bits CKS1 and
CKS0 in TCR. FRC can be cleared by compare-match A. When FRC overflows from H'FFFF to
H'0000, the overflow flag bit (OVF) in TCSR is set to 1. FRC should always be accessed in 16-bit
units; cannot be accessed in 8-bit units. FRC is initialized to H'0000.
9.3.2
The FRT has two output compare registers, OCRA and OCRB, each of which is a 16-bit
readable/writable register whose contents are continually compared with the value in FRC. When
a match is detected (compare-match), the corresponding output compare flag (OCFA or OCFB) is
set to 1 in TCSR. If the OEA or OEB bit in TOCR is set to 1, when the OCR and FRC values
match, the output level selected by the OLVLA or OLVLB bit in TOCR is output at the output
compare output pin (FTOA or FTOB). Following a reset, the FTOA and FTOB output levels are 0
until the first compare-match. OCR should always be accessed in 16-bit units; cannot be accessed
in 8-bit units. OCR is initialized to H'FFFF.
9.3.3
The FRT has four input capture registers, ICRA to ICRD, each of which is a 16-bit read-only
register. When the rising or falling edge of the signal at an input capture input pin (FTIA to FTID)
is detected, the current FRC value is transferred to the corresponding input capture register (ICRA
to ICRD). At the same time, the corresponding input capture flag (ICFA to ICFD) in TCSR is set
to 1. The FRC contents are transferred to ICR regardless of the value of ICF. The input capture
edge is selected by the input edge select bits (IEDGA to IEDGD) in TCR.
ICRC and ICRD can be used as ICRA and ICRB buffer registers, respectively, by means of buffer
enable bits A and B (BUFEA and BUFEB) in TCR. For example, if an input capture occurs when
ICRC is specified as the ICRA buffer register, the FRC contents are transferred to ICRA, and then
transferred to the buffer register ICRC.
To ensure input capture, the input capture pulse width should be at least 1.5 system clocks ( ) for
a single edge. When triggering is enabled on both edges, the input capture pulse width should be at
least 2.5 system clocks ( ).
ICRA to ICRD should always be accessed in 16-bit units; cannot be accessed in 8-bit units. ICR is
initialized to H'0000.
Rev. 2.00 Mar 21, 2006 page 150 of 518
REJ09B0299-0200
Free-Running Counter (FRC)
Output Compare Registers A and B (OCRA, OCRB)
Input Capture Registers A to D (ICRA to ICRD)