DF2110BVTE10 Renesas Electronics America, DF2110BVTE10 Datasheet - Page 495

• Manufacturer Part Number: DF2110BVTE10
• Description: MCU 3V 64K 100-TQFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2100r

Specifications of DF2110BVTE10

• Core Processor: H8S/2000
• Core Size: 16-Bit
• Speed: 10MHz
• Connectivity: Host Interface (LPC), I²C, SCI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 82
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 100-TQFP, 100-VQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Data Converters: -
• Other names: HD64F2110BVTE10; HD64F2110BVTE10

Section 19 Power-Down Modes
19.9
Subactive Mode
The CPU makes a transition to subactive mode when the SLEEP instruction is executed in high-
speed mode with the SSBY bit in SBYCR set to 1, the DTON bit and LSON bit in LPWRCR set
to 1, and the PSS bit in TCSR (WDT_1) set to 1. When an interrupt occurs in watch mode, and if
the LSON bit in LPWRCR is 1, a direct transition is made to subactive mode. Similarly, if an
interrupt occurs in subsleep mode, a transition is made to subactive mode.
In subactive mode, the CPU operates at a low speed based on the subclock and sequentially
executes programs. Peripheral modules other than TMR_0, TMR_1, WDT_0, and WDT_1 are
also stopped.
When operating the CPU in subactive mode, the SCK2 to SCK0 bits in SBYCR must be cleared to
0.
Subactive mode is exited by the SLEEP instruction, RES pin input, or STBY pin input.
When the SLEEP instruction is executed with the SSBY bit in SBYCR set to 1, the DTON bit in
LPWRCR cleared to 0, and the PSS bit in TCSR (WDT_1) set to 1, the CPU exits subactive mode
and a transition is made to watch mode. When the SLEEP instruction is executed with the SSBY
bit in SBYCR cleared to 0, the LSON bit in LPWRCR set to 1, and the PSS bit in TCSR (WDT_1)
set to 1, a transition is made to subsleep mode. When the SLEEP instruction is executed with the
SSBY bit in SBYCR set to 1, the DTON bit and LSON bit in LPWRCR set to 10, and the PSS bit
in TCSR (WDT_1) set to 1, a direct transition is made to high-speed mode.
For details of direct transitions, see section 19.11, Direct Transitions.
When the RES pin is driven low, system clock oscillation starts. Simultaneously with the start of
system clock oscillation, the system clock is supplied to the entire LSI. Note that the RES pin must
be held low until the clock oscillation is stabilized. If the RES pin is driven high after the clock
oscillation stabilization time has passed, the CPU begins reset exception handling.
If the STBY pin is driven low, the LSI enters hardware standby mode.
Rev. 2.00 Mar 21, 2006 page 455 of 518
REJ09B0299-0200