UPD78F1000GB-GAF-AX Renesas Electronics America, UPD78F1000GB-GAF-AX Datasheet - Page 472

• Manufacturer Part Number: UPD78F1000GB-GAF-AX
• Description: MCU 16BIT 78K0R/KX3-L 44-LQFP
• Manufacturer: Renesas Electronics America
• Series: 78K0R/Kx3-Lr

Specifications of UPD78F1000GB-GAF-AX

• Core Processor: 78K/0R
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: 3-Wire SIO, I²C, LIN, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 33
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

78K0R/Kx3-L
R01UH0106EJ0300 Rev.3.00
Oct 01, 2010
Figure 8-64. Example of Set Contents of Registers When One-Shot Pulse Output Function Is Used (Slave Channel)
Remark
TMRmp
TOMm
TOEm
TOLm
TOm
(a) Timer mode register mp (TMRmp)
(b) Timer output register m (TOm)
(c) Timer output enable register m (TOEm)
(d) Timer output level register m (TOLm)
(e) Timer output mode register m (TOMm)
TOMmp
TOEmp
CKSmp
TOLmp
Note
m: Unit number (m = 0, 1), n: Channel number (n = 0, 2, 4, 6)
78K0R/KC3-L, 78K0R/KD3-L, 78K0R/KE3-L: mn = 00, 02, 04, 06
78K0R/KF3-L, 78K0R/KG3-L:
p: Slave channel number
When m = 0: n < p ≤ 7
When m = 1: n < p ≤ 3
TOmp
Bit p
Bit p
Bit p
Bit p
1/0
1/0
1/0
1/0
15
1
Operation clock selection
14
0: Selects CKm0 as operation clock of channel p.
1: Selects CKm1 as operation clock of channel p.
0
Since there is no function of timer I/O, the channel 1 in the 78K0R/KC3-L (40-pin) can not be used
as the slave channel.
* Make the same setting as master channel.
0: Outputs 0 from TOmp.
1: Outputs 1 from TOmp.
0: Stops the TOmp output operation by counting operation.
1: Enables the TOmp output operation by counting operation.
0: Positive logic output (active-high)
1: Inverted output (active-low)
1: Sets the slave channel output mode.
13
0
CCSmp
12
0
Count clock selection
Note
TERmp
MAS
11
0: Selects operation clock.
0
Slave/master selection
STSmp2
10
0: Slave channel.
1
STSmp1
0
9
Start trigger selection
STSmp0
100B: Selects INTTMmn of master channel.
8
0
mn = 00, 02, 04, 06, 10, 12
CISmp1
7
0
CISmp0
6
0
Selection of TImp pin input edge
00B: Sets 00B because these are not used.
Operation mode of channel p
100B: One-count mode
5
0
CHAPTER 8 TIMER ARRAY UNIT
4
0
Start trigger during operation
MDmp3
0: Trigger input is invalid.
3
1
MDmp2
2
0
MDmp1
1
0
MDmp0
0
0
472