DS3181 Maxim Integrated Products, DS3181 Datasheet - Page 185

• Manufacturer Part Number: DS3181
• Description: Network Controller & Processor ICs DS3-E3 ATM-Packet PH Y with Built-in Line
• Manufacturer: Maxim Integrated Products

Specifications of DS3181

• Product: Framer
• Number Of Transceivers: 1
• Data Rate: 44.736 Mbps
• Supply Voltage (max): 3.465 V
• Supply Voltage (min): 3.135 V
• Supply Current (max): 280 mA
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Package / Case: TEBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

trace identifier data to the microprocessor via the microprocessor interface using register timing. The data is forced
to all ones during LOS, LOF and AIS detection to eliminate false messages
The transmit direction inputs the trace identifier data from the microprocessor via the microprocessor interface and
stores the trace identifier data in the data storage using register timing. It removes the trace identifier data from the
data storage, performs trace ID processing, and outputs the trace ID data stream. See
of the Trail Trace Controller with the DS318x devices.
Figure 10-47. Trail Trace Controller Block Diagram
10.12.2 Features
•
•
•
•
•
•
•
•
10.12.3 Functional Description
The bits in a byte are received most significant bit (MSB) first and least significant bit (LSB) last. When they are
output serially, they are output MSB first and LSB last. The bits in a byte in an incoming signal are numbered in the
order they are received, 1 (MSB) to 8 (LSB). However, when a byte is stored in a register, the MSB is stored in the
highest numbered bit (7), and the LSB is stored in the lowest numbered bit (0). This is to differentiate between a
byte in a register and the corresponding byte in a signal.
Clock Rate
Programmable trail trace ID – The trail trace ID controller can be programmed to handle a 16-byte trail trace
identifier (trail trace mode).
Programmable transmit trace ID – All 16 bytes of the transmit trail trace identifier are programmable.
Programmable receive expected trace ID – A 16-byte expected trail trace identifier can be programmed.
Both a mismatch and unstable indication are provided.
Programmable trace ID multiframe alignment – The transmit side can be programmed to perform trail trace
multiframe alignment insertion. The receive side can be programmed to perform trail trace Multiframe
synchronization.
Programmable bit reordering – The trace identifier data can be output MSB first or LSB first from the data
storage.
Programmable data inversion – The trace identifier data can be inverted immediately after trace ID
processing on the transmit side, and immediately before trail ID processing on the receive side.
Fully independent transmit and receive sides
Fully independent Line side and register interface timing – The data storage can be read from or written to
via the microprocessor interface while all line side clocks and signals are inactive, and read from or written to
via the line side while all microprocessor interface clocks and signals are inactive.
Receive
Transmit
DS3/E3
DS3/E3
Adapter
LIU
LIU
Decoder
Encoder
B3ZS/
B3ZS/
HDB3
HDB3
TUA1
TAIS
IEEE P1149.1
Access Port
JTAG Test
FEAC
DS3 / E3
Receive
Framer
Formatter
DS3 / E3
Transmit
Buf f er
Trace
Trail
HDLC
UA1
GEN
185
TX FRAC/
PLCP
RX FRAC/
PLCP
Processor
Processor
Rx Packet
Processor
Processor
Tx Packet
RX BERT
TX BERT
Rx Cell
Tx Cell
Microprocessor
Interface
Figure 10-47
FIFO
FIFO
Tx
Rx
for the location