UPD78F1233GB-GAH-AX Renesas Electronics America, UPD78F1233GB-GAH-AX Datasheet - Page 287

• Manufacturer Part Number: UPD78F1233GB-GAH-AX
• Description: MCU 16BIT 78K0R/LX3 64-LQFP
• Manufacturer: Renesas Electronics America
• Series: 78K0R/Ix3r

Specifications of UPD78F1233GB-GAH-AX

• Core Processor: 78K/0R
• Core Size: 16-Bit
• Speed: 40MHz
• Connectivity: 3-Wire SIO, I²C, LIN, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 50
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Address: F0190H, F0191H (TMR00) to F019EH, F019FH (TMR07)
Symbol
TMRn
Notes 1. These settings are used with the inverter control function. For the inverter control function, refer to
Remark
F01C8H, F01C9H (TMR08) to F01CEH, F01CFH (TMR11)
The operation of the MDn0 bit varies depending on each operation mode (see table below).
• Interval timer mode
• Capture mode
• Event counter mode
• Up and down count mode
• One-count mode
• Capture & one-count mode
CKS
2. In one-count mode, interrupt output (INTTMn) when starting a count operation and TOn output are
3. If the start trigger (TSn = 1) is issued during operation, the counter is cleared, an interrupt is
MD
n4
15
0
0
0
0
0
1
n
(0, 0, 1, 0)
(0, 0, 1, 1)
(1, 0, 0, 1)
(0, 1, 0, 0)
(0, 1, 1, 0)
(0, 0, 0, 0)
(Value set by the MDn4 to MDn1 bits
CHAPTER 7 INVERTER CONTROL FUNCTIONS.
not controlled.
generated, and recounting is started.
n = 00 to 11
MD
n3
Other than above
14
0
0
0
1
1
0
0
(see table above))
Operation mode
CCS
MD
Figure 6-7. Format of Timer Mode Register n (TMRn) (3/3)
n2
13
1n
0
1
1
0
1
0
Other than above
Note 2
CCS
MD
n1
12
0n
0
0
1
0
0
1
Note 1
CHAPTER 6 TIMER ARRAY UNIT TAUS
MAST
ERn
MD
1/0
1/0
1/0
11
n0
0
0
0
User’s Manual U19678EJ1V1UD
Interval timer mode
Capture mode
Event counter mode
One-count mode
Capture & one-count mode
Up and down count mode
Setting prohibited
STS
10
n2
Operation mode of channel n
STS
n1
9
MD
n0
0
1
0
0
1
0
STS
n0
8
Timer interrupt is not generated when counting is started
(timer output does not change, either).
Timer interrupt is generated when counting is started
(timer output also changes).
Timer interrupt is not generated when counting is started
(timer output does not change, either).
Start trigger is invalid during counting operation.
At that time, interrupt is not generated, either.
Start trigger is valid during counting operation
At that time, interrupt is also generated.
Timer interrupt is not generated when counting is started
(timer output does not change, either).
Start trigger is invalid during counting operation.
At that time, interrupt is not generated, either.
Setting prohibited
After reset: 0000H
CIS
n1
7
Note 1
Setting of starting counting and interrupt
CIS
n0
6
Counting down
Counting up
Counting down
Counting down
Counting up
Counting up and down
Count operation of TCR
5
0
R/W
MD
n4
4
MD
n3
3
MD
n2
2
Note 3
Independent
Possible
Possible
Possible
Impossible
Possible
Impossible
.
MD
n1
operation
1
MD
n0
285
0