UPD78F1233GB-GAH-AX Renesas Electronics America, UPD78F1233GB-GAH-AX Datasheet - Page 428

• Manufacturer Part Number: UPD78F1233GB-GAH-AX
• Description: MCU 16BIT 78K0R/LX3 64-LQFP
• Manufacturer: Renesas Electronics America
• Series: 78K0R/Ix3r

Specifications of UPD78F1233GB-GAH-AX

• Core Processor: 78K/0R
• Core Size: 16-Bit
• Speed: 40MHz
• Connectivity: 3-Wire SIO, I²C, LIN, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 50
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

426
(a) Timer mode register 00 (TMR00)
(b) Other registers
TMR00
Figure 7-41. Example of Set Contents of Registers of 6-Phase Triangular Wave PWM Output Function
Notes 1.
CKS00
1/0
TOE0:TOE00
TO0:TO00
TOM0:TOM00
TOT0:TOT00
TOL0:TOL00
TDE0:TDE00
TRE0:TRE00
TRO0:TRO00
TRC0:TRC00
TME0:TME00
15
2.
Operation clock selection
0: Selects CK00 as operation clock of channel 0.
1: Selects CK01 as operation clock of channel 0.
14
0
Note 2
Set TOE00 of the master channel to “1” in the following cases.
CCS100
Note 1
• When an INTTMM0, INTTMV0, INTTMM1, or INTTMV1 interrupt signal is used
• When Hi-Z output is controlled or an A/D conversion trigger is selected via control by using
When MD000 = 1, TO00 is set to 0.
When MD000 = 0, TO00 is set to 1
13
0
the OPMR, OPHS, OPHT, and OPCR registers
CCS000
0: Stops the TO00 output operation by counting operation.
1: Enables the TO00 output operation by counting operation.
0: Outputs a low level from TO00.
1: Outputs a high level from TO00.
0: Sets master channel output mode.
0: Sets 0 when TOM00 = 0 (master channel output mode).
0: Sets 0 when TOM00 = 0 (master channel output mode).
0: Stops dead time control.
0: Stops real-time output.
0: Sets 0 when TRE00 = 0 (stops real-time output).
0: Does not operate as the real-time output trigger generation channel.
0: Stops modulated output.
12
0
CHAPTER 7 INVERTER CONTROL FUNCTIONS
TER00
Count clock selection
MAS
00B: Selects operation clock.
11
1
STS002
Slave/master selection
1: Master channel
10
0
User’s Manual U19678EJ1V1UD
STS001
(Master Channel)
0
9
STS000
Start trigger selection
000B: Selects only software start.
0
8
CIS001
0
7
CIS000
0
6
Selection of TI00 pin input edge
00B: Sets 00B because these are not used.
Operation mode of channel 0
0000B: Interval timer
0
5
MD004
4
0
Setting of operation when
counting is started
0: Neither generates INTTM00
1: Generates INTTM00 and
MD003
3
0
nor inverts timer output
when counting is started.
inverts timer output when
counting is started.
MD002
2
0
MD001
1
0
MD000
1/0
0