BMSKTOPASA900(DCE) Toshiba, BMSKTOPASA900(DCE) Datasheet - Page 574

• Manufacturer Part Number: BMSKTOPASA900(DCE)
• Description: KIT STARTER TMPA900 USB JTAG
• Manufacturer: Toshiba
• Series: TOPASr
• Type: MCUr

Specifications of BMSKTOPASA900(DCE)

• Contents: Evaluation Board, Cable(s), Software and Documentation
• For Use With/related Products: TMPA900CMXBG
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

[31:16]
[15]
[14]
[13]
[12]
[11]
[10]
[9]
[8]
[7]
[6]
[5]
[4]
[3]
[2]
[1]
[0]
Bit
[Description]
−
m_nak
m_ep
m_ep0
m_sof
m_rx_data0
m_status
m_status_nak
m_setup
i_nak
i_ep
i_ep0
i_sof
i_rx_data0
i_status
i_status_nak
i_setup
a. <m_nak>
b. <m_ep>
Note: The lower byte (bits 7-0) will be cleared by writing 1 to the relevant bits.
Symbol
Bit
(3) Interrupt Control registers
1.
Sets whether or not to output "i_nak (bit 7)" to the INT_NAK pin.
0y0: Enable (output)
0y1: Disable (no output)
Sets whether or not to output "i_ep (bit 6)" to the INT_EP pin.
0y0: Enable (output)
0y1: Disable (no output)
UD2INT (INT register)
−
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Type
Undefined
0y0
0y0
0y0
0y0
0y0
0y0
0y0
0y0
0y0
0y0
0y0
0y0
0y0
0y0
0y0
0y0
Reset
Value
TENTATIVE
TMPA900CM- 573
Read as undefined. Write as zero.
Sets whether or not to output "i_nak (bit 7)" to the INT_NAK pin.
0y0: Enable (output) 0y1: Disable (no output)
Sets whether or not to output "i_ep (bit 6)" to the INT_EP pin.
0y0: Enable (output) 0y1: Disable (no output)
Sets whether or not to output "i_ep0 (bit 5)" to the INT_EP0 pin.
0y0: Enable (output) 0y1: Disable (no output)
Sets whether or not to output "i_sof (bit 4)" to the INT_SOF pin.
0y0: Enable (output) 0y1: Disable (no output)
Sets whether or not to output "i_rx_data0 (bit 3)" to the
INT_RX_ZERO pin.
0y0: Enable (output) 0y1: Disable (no output)
Sets whether or not to output "i_status (bit 2)" to the INT_STATUS
pin.
0y0: Enable (output) 0y1: Disable (no output)
Sets whether or not to output "i_status_nak(bit1)" to the
INT_STATUS_NAK pin.
0y0: Enable (output) 0y1: Disable (no output)
Sets whether or not to output "i_setup (bit 0)" to the INT_SETUP
pin.
0y0: Enable (output) 0y1: Disable (no output)
This will be set to 1 when NAK is transmitted by EPs except EP0.
This will be set to 1 when transfers to EPs other than EP0 have
successfully finished
This will be set to 1 when the transfer to EP0 has successfully
finished.
This will be set to 1 when the SOF-token is received or after 1
frame-time was counted in the create_sof mode.
This will be set to 1 when Zero-Length data is received.
This will be set to 1 when the STATUS-Stage has successfully
finished in Control transfers at EP0.
This will be set to 1 when “NAK” is reruned during packet reception
of the STATUS-Stage during Control-RD transfer to EP0.
This will be set to 1 when the Setup-Token was received in Control
transfers at EP0.
Description
Address = (0xF440_0000) + (0x0220)
TMPA900CM
2009-10-14