DF2211NP24V Renesas Technology / Hitachi Semiconductor, DF2211NP24V Datasheet - Page 263
DF2211NP24V
Manufacturer Part Number
DF2211NP24V
Description
H8S/2200 Series, 2212 Group, USB, RTC, HSS TNP-64B; Vcc= 2.7 to 3.6 volts, Temp= -20 to 75 C; Package: PVQN0064LB-A
Manufacturer
Renesas Technology / Hitachi Semiconductor
Datasheet
1.DF2211NP24V.pdf
(756 pages)
- Current page: 263 of 756
- Download datasheet (5Mb)
7.6.4
At the start of activation source acceptance, a low level is detected in both DREQ signal falling
edge sensing and low level sensing. Similarly, in the case of an internal interrupt, the interrupt
request is detected. Therefore, a request is accepted from an internal interrupt or DREQ pin low
level that occurs before execution of the DMABCRL write to enable transfer.
When the DMAC is activated, take any necessary steps to prevent an internal interrupt or DREQ
signal low level remaining from the end of the previous transfer, etc.
7.6.5
When the DTE bit is cleared to 0 by the end of transfer or an abort, the selected internal interrupt
request will be sent to the CPU even if DTA is set to 1.
Also, if internal DMAC activation has already been initiated when operation is aborted, the
transfer is executed but flag clearing is not performed for the selected internal interrupt even if
DTA is set to 1.
An internal interrupt request following the end of transfer or an abort should be handled by the
CPU as necessary.
7.6.6
To reactivate a number of channels when multiple channels are enabled, use exclusive handling of
transfer end interrupts, and perform DMABCR control bit operations exclusively. Note, in
particular, that in cases where multiple interrupts are generated between reading and writing of
DMABCR, and a DMABCR operation is performed during new interrupt handling, the DMABCR
write data in the original interrupt handling routine will be incorrect, and the write may invalidate
the results of the operations by the multiple interrupts. Ensure that overlapping DMABCR
operations are not performed by multiple interrupts, and that there is no separation between read
and write operations by the use of a bit-manipulation instruction. Also, when the DTE and DTME
bits are cleared by the DMAC or are written with 0, they must first be read while cleared to 0
before the CPU can write a 1 to them.
Activation Source Acceptance
Internal Interrupt after End of Transfer
Channel Re-Setting
Rev.7.00 Dec. 24, 2008 Page 209 of 698
REJ09B0074-0700
Related parts for DF2211NP24V
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
CONN SOCKET 2POS 7.92MM WHITE
Manufacturer:
Hirose Electric Co Ltd
Datasheet:
Part Number:
Description:
CONN SOCKET 4POS 7.92MM WHITE
Manufacturer:
Hirose Electric Co Ltd
Datasheet:
Part Number:
Description:
CONN SOCKET 5POS 7.92MM WHITE
Manufacturer:
Hirose Electric Co Ltd
Datasheet:
Part Number:
Description:
CONN SOCKET 3POS 7.92MM WHITE
Manufacturer:
Hirose Electric Co Ltd
Datasheet:
Part Number:
Description:
CONN SOCKET 5POS 7.92MM WHITE
Manufacturer:
Hirose Electric Co Ltd
Datasheet:
Part Number:
Description:
CONN SOCKET 2POS 7.92MM WHITE
Manufacturer:
Hirose Electric Co Ltd
Datasheet:
Part Number:
Description:
CONN SOCKET 3POS 7.92MM WHITE
Manufacturer:
Hirose Electric Co Ltd
Datasheet:
Part Number:
Description:
CONN SOCKET 4POS 7.92MM WHITE
Manufacturer:
Hirose Electric Co Ltd
Datasheet:
Part Number:
Description:
CONN HEADER 2POS 7.92MM R/A TIN
Manufacturer:
Hirose Electric Co Ltd
Datasheet:
Part Number:
Description:
CONN HEADER 4POS 7.92MM R/A TIN
Manufacturer:
Hirose Electric Co Ltd
Datasheet:
Part Number:
Description:
Renesas MCU
Manufacturer:
Renesas Technology / Hitachi Semiconductor
Datasheet:
Part Number:
Description:
Renesas MCU
Manufacturer:
Renesas Technology / Hitachi Semiconductor
Datasheet:
Part Number:
Description:
1.5 Channel Motor Driver with DC/DC Control
Manufacturer:
Renesas Technology / Hitachi Semiconductor
Part Number:
Description:
Accessories, Interface Cable
Manufacturer:
Renesas Technology / Hitachi Semiconductor
Datasheet: