EP4SGX360FH29C3N Altera, EP4SGX360FH29C3N Datasheet - Page 368

• Manufacturer Part Number: EP4SGX360FH29C3N
• Description: IC STRATIX IV FPGA 360K 780HBGA
• Manufacturer: Altera
• Series: Stratix® IV GXr

Specifications of EP4SGX360FH29C3N

• Number Of Logic Elements/cells: 353600
• Number Of Labs/clbs: 14144
• Total Ram Bits: 22564
• Number Of I /o: 289
• Voltage - Supply: 0.87 V ~ 0.93 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 780-HBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -

10–34
Figure 10–15. Multi-Device PS Configuration Using a USB Blaster, EthernetBlaster, MasterBlaster, ByteBlaster II, or
ByteBlasterMV Cable
Notes to
(1) Connect the pull-up resistor to the same supply voltage (V
(2) You only need the pull-up resistors on DATA0 and DCLK if the download cable is the only configuration scheme used on your board. This is to
(3) Pin 6 of the header is a V
Stratix IV Device Handbook Volume 1
EthernetBlaster cable.
ensure that DATA0 and DCLK are not left floating after configuration. For example, if you are also using a configuration device, you do not need
the pull-up resistors on DATA0 and DCLK.
this value, refer to the
this pin is a no connect.
Figure
10–15:
10 kΩ
V
CCPGM
10 kΩ
V
MasterBlaster Serial/USB Communications Cable User
CCPGM
(1)
You can use a download cable to configure multiple Stratix IV devices by connecting
each device’s nCEO pin to the subsequent device’s nCE pin. The first device’s nCE pin is
connected to GND, while its nCEO pin is connected to the nCE of the next device in the
chain. The last device’s nCE input comes from the previous device, while its nCEO pin is
left floating. All other configuration pins (nCONFIG, nSTATUS, DCLK, DATA0, and
CONF_DONE) are connected to every device in the chain. Because all CONF_DONE pins are
tied together, all devices in the chain initialize and enter user mode at the same time.
In addition, because the nSTATUS pins are tied together, the entire chain halts
configuration if any device detects an error. The Auto-restart configuration after
error option does not affect the configuration cycle because you must manually restart
the configuration in the Quartus II software when an error occurs.
Figure 10–15
cable.
IO
reference voltage for the MasterBlaster output driver. V
(2)
(1)
V
V
CCPGM
CCPGM
GND
GND
GND
(1)
(1)
shows how to configure multiple Stratix IV devices with a download
Chapter 10: Configuration, Design Security, and Remote System Upgrades in Stratix IV Devices
MSEL2
MSEL1
MSEL0
Stratix IV Device 1
MSEL2
MSEL1
MSEL0
DATA0
nCONFIG
nCONFIG
nCE
Stratix IV Device 2
nCE
DATA0
CONF_DONE
CONF_DONE
nSTATUS
nSTATUS
CCPGM
DCLK
nCEO
nCEO
DCLK
) as the USB Blaster, MasterBlaster (VIO pin), ByteBlaster II, ByteBlasterMV, or
10 kΩ
V
N.C.
CCPGM
10 kΩ
Guide. In the USB-Blaster, ByteBlaster II, and ByteBlasterMV cables,
V
(1)
CCPGM
IO
must match the device’s V
(1)
10 kΩ
V
CCPGM
(2)
(1)
10-Pin Male Header
Pin 1
Download Cable
(PS Mode)
CCPGM
GND
April 2011 Altera Corporation
V
CCPGM
. For more information about
Passive Serial Configuration
V
GND
IO
(1)
(3)