EP4SGX360FH29C3N Altera, EP4SGX360FH29C3N Datasheet - Page 755

• Manufacturer Part Number: EP4SGX360FH29C3N
• Description: IC STRATIX IV FPGA 360K 780HBGA
• Manufacturer: Altera
• Series: Stratix® IV GXr

Specifications of EP4SGX360FH29C3N

• Number Of Logic Elements/cells: 353600
• Number Of Labs/clbs: 14144
• Total Ram Bits: 22564
• Number Of I /o: 289
• Voltage - Supply: 0.87 V ~ 0.93 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 780-HBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -

© 2011 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX are Reg. U.S. Pat. & Tm. Off.
and/or trademarks of Altera Corporation in the U.S. and other countries. All other trademarks and service marks are the property of their respective holders as described at
www.altera.com/common/legal.html. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera’s standard warranty, but
reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any
information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device
specifications before relying on any published information and before placing orders for products or services.
SIV52003-4.1
Overview
Stratix IV Device Handbook Volume 2: Transceivers
February 2011
February 2011
SIV52003-4.1
f
This chapter describes the procedure for merging; for example, when combining
multiple protocols and data rates within a transceiver block. The instances you can
combine include Receiver Only and Transmitter and Receiver channels as well as
channels configured in Protocol Functional modes, channels using PLL cascade
clocks, channels in multiple transceiver blocks, and channels with a Basic (PMA
Direct) configuration. This chapter also offers several examples of sharing the clock
multiplier unit phase-locked loops (CMU PLLs).
For information about the supported data rate range for the auxiliary transmit
(ATX) PLL, refer to the “Transceiver Performance Specifications” section in the
and Switching Characteristics for Stratix IV Devices
Each transceiver channel in a Stratix
data rate or in an independent protocol mode. Within each transceiver channel, the
transmitter and receiver channels can run at different data rates. Each transceiver
block consists of two CMU PLLs that provide clocks to all the transmitter channels
within the transceiver block. Each receiver channel contains a dedicated clock data
recovery (CDR) unit.
In addition to the CMU PLLs, the ATX PLLs are available to provide clocks to the
transmitter channels that are configured for a specific data rate range.
This chapter includes the following sections:
■
■
■
■
■
■
■
■
■
■
■
■
“Glossary of Terms” on page 3–2
“Creating Transceiver Channel Instances” on page 3–3
“General Requirements to Combine Channels” on page 3–3
“Sharing CMU PLLs” on page 3–5
“Sharing ATX PLLs” on page 3–10
“Combining Receiver Only Channels” on page 3–10
“Combining Transmitter Channel and Receiver Channel Instances” on page 3–11
“Combining Transceiver Instances in Multiple Transceiver Blocks” on page 3–13
“Combining Transceiver Instances Using PLL Cascade Clocks” on page 3–16
“Combining Channels Configured in Protocol Functional Modes” on page 3–17
“Combining Transceiver Channels in Basic (PMA Direct) Configurations” on
page 3–25
“Combination Requirements When You Enable Channel Reconfiguration” on
page 3–42
3. Configuring Multiple Protocols and
Data Rates in Stratix IV Devices
®
IV GX and GT device can run at an independent
chapter.
DC
Subscribe