LFEBS12UB Freescale Semiconductor, LFEBS12UB Datasheet - Page 478

• Manufacturer Part Number: LFEBS12UB
• Description: KIT STUDENT LEARNING S12 DG128
• Manufacturer: Freescale Semiconductor

Specifications of LFEBS12UB

• Architecture: 8/16-bit
• Code Gen Tools Included: Code Warrior
• Silicon Manufacturer: Freescale
• Core Architecture: S12
• Core Sub-architecture: S12
• Silicon Core Number: MC9S12
• Silicon Family Name: S12D
• Kit Contents: HCS12 DG128 Learning Kit
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Chapter 11 S12XE Clocks and Reset Generator (S12XECRGV1)
11.3.2.5
This register enables S12XECRG interrupt requests.
478
Module Base + 0x0004
Because of an order from the United States International Trade Commission, BGA-packaged product lines and partnumbers
LOCKIF
SCMIF
Reset
PORF
LOCK
indicated here currently are not available from Freescale for import or sale in the United States prior to September 2010
LVRF
Field
RTIF
SCM
ILAF
7
6
5
4
3
2
1
0
W
R
RTIE
Real Time Interrupt Flag — RTIF is set to 1 at the end of the RTI period. This flag can only be cleared by writing
a 1. Writing a 0 has no effect. If enabled (RTIE=1), RTIF causes an interrupt request.
0 RTI time-out has not yet occurred.
1 RTI time-out has occurred.
Power on Reset Flag — PORF is set to 1 when a power on reset occurs. This flag can only be cleared by writing
a 1. Writing a 0 has no effect.
0 Power on reset has not occurred.
1 Power on reset has occurred.
Low Voltage Reset Flag — LVRF is set to 1 when a low voltage reset occurs. This flag can only be cleared by
writing a 1. Writing a 0 has no effect.
0 Low voltage reset has not occurred.
1 Low voltage reset has occurred.
IPLL Lock Interrupt Flag — LOCKIF is set to 1 when LOCK status bit changes. This flag can only be cleared
by writing a 1. Writing a 0 has no effect.If enabled (LOCKIE=1), LOCKIF causes an interrupt request.
0 No change in LOCK bit.
1 LOCK bit has changed.
Lock Status Bit — LOCK reflects the current state of IPLL lock condition. This bit is cleared in Self Clock Mode.
Writes have no effect.
0 VCOCLK is not within the desired tolerance of the target frequency.
1 VCOCLK is within the desired tolerance of the target frequency.
Illegal Address Reset Flag — ILAF is set to 1 when an illegal address reset occurs. Refer to S12XMMC Block
Guide for details. This flag can only be cleared by writing a 1. Writing a 0 has no effect.
0 Illegal address reset has not occurred.
1 Illegal address reset has occurred.
Self Clock Mode Interrupt Flag — SCMIF is set to 1 when SCM status bit changes. This flag can only be
cleared by writing a 1. Writing a 0 has no effect. If enabled (SCMIE=1), SCMIF causes an interrupt request.
0 No change in SCM bit.
1 SCM bit has changed.
Self Clock Mode Status Bit — SCM reflects the current clocking mode. Writes have no effect.
0 MCU is operating normally with OSCCLK available.
1 MCU is operating in Self Clock Mode with OSCCLK in an unknown state. All clocks are derived from PLLCLK
S12XECRG Interrupt Enable Register (CRGINT)
0
7
running at its minimum frequency f
= Unimplemented or Reserved
Figure 11-7. S12XECRG Interrupt Enable Register (CRGINT)
0
0
6
MC9S12XE-Family Reference Manual , Rev. 1.23
Table 11-4. CRGFLG Field Descriptions
5
0
0
SCM
.
LOCKIE
0
4
Description
0
0
3
2
0
0
Freescale Semiconductor
SCMIE
0
1
0
0
0