MPC561MZP56 Freescale, MPC561MZP56 Datasheet - Page 1150
MPC561MZP56
Manufacturer Part Number
MPC561MZP56
Description
Manufacturer
Freescale
Datasheet
1.MPC561MZP56.pdf
(1420 pages)
Specifications of MPC561MZP56
Cpu Family
MPC56x
Device Core
PowerPC
Device Core Size
32b
Frequency (max)
56MHz
Interface Type
QSPI/SCI/SPI/UART
Total Internal Ram Size
32KB
# I/os (max)
56
Number Of Timers - General Purpose
22
Operating Supply Voltage (typ)
2.6/5V
Operating Supply Voltage (max)
2.7/5.25V
Operating Supply Voltage (min)
2.5/4.75V
On-chip Adc
2(32-chx10-bit)
Instruction Set Architecture
RISC
Operating Temp Range
-40C to 125C
Operating Temperature Classification
Automotive
Mounting
Surface Mount
Pin Count
388
Package Type
BGA
Program Memory Type
ROMLess
Program Memory Size
Not Required
Lead Free Status / RoHS Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MPC561MZP56
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
MPC561MZP56R2
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
- Current page: 1150 of 1420
- Download datasheet (11Mb)
Clock and Board Guidelines
C.2.3
C
The maximum noise allowed on XFC is 50 mV peak-to-peak with a typical cut-off frequency of 500 Hz.
The XFC capacitor creates a low pass filter in the PLL loop. The filter output feeds the PLL VCO. The
capacitor is charged and discharged by short current pulses, generated by the phase detector. So the
capacitor leakage and absorption directly affect the AC component in the VCO input voltage that creates
PLL output clock jitter. Therefore, the dielectric quality of C
Smaller C
but slower to gain lock. Because each board layout and application is unique, C
a system.
The minimum required value (including capacitor tolerance) for C
cases:
C-6
XFC
is the PLL feedback capacitor. It must be located as close as possible to the XFC and VDDSYN pads.
0 < (MF+1) < 4
(MF+1) >= 4
XFC
PLL Off-Chip Capacitor C
makes the PLL faster to gain lock but less stable. Higher C
Note: A filter cut off frequency of 500Hz is recommended, however this will result in a
capacitor size of 33uF using a 10 Ohm resistor. This may be too expensive or large
for the system. In this case the filter shown with cut- off frequency of 160kHz will suffice.
Note: A filter cut off frequency of 500Hz is recommended, however this will result in a
capacitor size of 15uF using a 8.2mH inductor. This may be too expensive or large
for the system. In this case the filter shown with cut- off frequency of 5.5kHz will suffice.
Keyed
VDD 2.6 V
Keyed
VDD 2.6 V
Figure C-7. LC Filter Example (Alternative)
MPC561/MPC563 Reference Manual, Rev. 1.2
8.2 mH
Board
Board
10 Ω
Figure C-6. RC Filter Example
100 nF
100 nF
VSSSYN
VSSSYN
XFC
C
C
XFC
XFC
= (2100 * (MF+1)) pF
= (1130 * (MF+1) – 80) pF
MPC56x Device
MPC56x Device
XFC
VDDSYN
XFC
VDDSYN
should be high.
is determined by the following two
XFC
makes the PLL more stable
XFC
must be evaluated in
Freescale Semiconductor
Related parts for MPC561MZP56
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
MPC5 1K0 5%
Manufacturer:
TE Connectivity
Datasheet:
Part Number:
Description:
MPC5 500R 5%
Manufacturer:
TE Connectivity
Datasheet:
Part Number:
Description:
MPC5 5K0 5%
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
MPC5 5R0 5%
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
MPC5 50K 5%
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
MPC5 1R0 5%
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
TOWER ELEVATOR BOARDS HARDWARE
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
TOWER SERIAL I/O HARDWARE
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
LCD MODULE FOR TWR SYSTEM
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
DAUGHTER LCD WVGA I.MX51
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
TOWER SYSTEM BOARD MPC5125
Manufacturer:
Freescale Semiconductor
Datasheet: