EP4SGX530HH35C2N Altera, EP4SGX530HH35C2N Datasheet - Page 855

• Manufacturer Part Number: EP4SGX530HH35C2N
• Description: IC STRATIX IV FPGA 530K 1152HBGA
• Manufacturer: Altera
• Series: Stratix® IV GXr

Specifications of EP4SGX530HH35C2N

• Number Of Logic Elements/cells: 531200
• Number Of Labs/clbs: 21248
• Total Ram Bits: 27376
• Number Of I /o: 564
• Voltage - Supply: 0.87 V ~ 0.93 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 1152-HBGA
• Family Name: Stratix® IV
• Number Of Logic Blocks/elements: 531200
• # Registers: 424960
• # I/os (max): 560
• Process Technology: 40nm
• Operating Supply Voltage (typ): 900mV
• Logic Cells: 531200
• Ram Bits: 28033024
• Operating Supply Voltage (min): 0.87V
• Operating Supply Voltage (max): 0.93V
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 1152
• Package Type: FCHBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Compliant

Chapter 5: Dynamic Reconfiguration in Stratix IV Devices
Quartus II MegaWizard Plug-In Manager Interfaces to Support Dynamic Reconfiguration
February 2011 Altera Corporation
Logical Channel Addressing—Combination of Regular Transceiver Channels and PMA-Only
Channels
For a combination of regular transceiver channels and PMA-only channels, there must
be at least two different ALTGX instances connected to the same dynamic
reconfiguration controller. This is because you cannot have a combination of regular
transceiver channels and PMA-only channels within the same ALTGX instance.
Set the starting channel number in the first ALTGX Instance 1 to 0. If you have
configured ALTGX Instance 1 with regular transceiver channels, the logical channel
addresses of the remaining channels increment in steps of one.
Set the starting channel number of the following ALTGX Instance 2 as the next
multiple of four. If you have configured ALTGX Instance 2 with PMA-only channels,
the logical channel addresses of the remaining channels increment in steps of four.
Figure 5–41
number for multiple ALTGX instances controlled by a single dynamic reconfiguration
controller, where one ALTGX instance has PMA-only channels and the other ALTGX
instance has regular transceiver channels.
Table 5–18
channel address of both the PMA-only channels and regular transceiver channels is
set based on the starting channel number.
For more information, refer to
Table 5–4
channel in a Stratix IV device.
The maximum number of transceiver channels in the largest Stratix IV device is 48
(24 transceiver channels located in four transceiver blocks on the right side of the
device and 24 transceiver channels located in four transceiver blocks on the left side of
the device).
You can individually configure these 48 transceiver channels as 48 Transmitter only
and 48 Receiver only channels. You achieve this by using 48 Transmitter only ALTGX
instances and 48 Receiver only ALTGX instances in your design.
Highest Possible Logical Channel Address
lists the highest possible logical channel address assigned to a transceiver
in
in
“Example 1” on page 5–94
“Example 1” on page 5–94
“Example 1” on page
lists an example scenario where the logical
shows how to set the starting channel
Stratix IV Device Handbook Volume 2: Transceivers
5–94.
5–9