MK30DN512ZVLK10 Freescale Semiconductor, MK30DN512ZVLK10 Datasheet - Page 1345

• Manufacturer Part Number: MK30DN512ZVLK10
• Description: ARM Microcontrollers - MCU KINETIS 512K SLCD
• Manufacturer: Freescale Semiconductor

Specifications of MK30DN512ZVLK10

• Core: ARM Cortex M4
• Processor Series: K30
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 50 MHz
• Program Memory Size: 512 KB
• Data Ram Size: 128 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 1.71 V to 3.6 V
• Operating Temperature Range: - 40 C to + 105 C
• Package / Case: LQFP-80
• Mounting Style: SMD/SMT

1. CMD3 differs for MMC and SD cards. For MMC cards, it is referred to as SET_RELATIVE_ADDR, with a response type of
2. CMD6 differs completely between high speed MMC cards and high speed SD cards. Command SWITCH_FUNC is for
3. Command SWITCH is for high speed MMC cards as well as for CE-ATA cards over the MMC interface. The Index field can
4. ACMDs shall be preceded with the APP_CMD command. (Commands listed are used for SD only, other SD commands
5. ACMDs shall be preceded with the APP_CMD command. (Commands listed are used for SD only, other SD commands
6. ACMDs shall be preceded with the APP_CMD command. (Commands listed are used for SD only, other SD commands
7. ACMDs shall be preceded with the APP_CMD command. (Commands listed are used for SD only, other SD commands
8. ACMDs shall be preceded with the APP_CMD command. (Commands listed are used for SD only, other SD commands
9. ACMDs shall be preceded with the APP_CMD command. (Commands listed are used for SD only, other SD commands
10. ACMDs shall be preceded with the APP_CMD command. (Commands listed are used for SD only, other SD commands
The Access Bits for the EXT_CSD Access Modes are shown in the following table.
45.7 Software restrictions
Software for the SDHC must observe the following restrictions.
Freescale Semiconductor, Inc.
ACMD51
CMD INDEX
R1. For SD cards, it is referred to as SEND_RELATIVE_ADDR, with a response type of R6 (with RCA inside).
high speed SD cards.
contain any value from 0-255, but only values 0-191 are valid. If the Index value is in the 192-255 range the card does not
perform any modification and the SWITCH_ERROR status bit in the EXT_CSD register is set. The Access Bits are shown
in
not listed are not supported on this module).
not listed are not supported on this module).
not listed are not supported on this module).
not listed are not supported on this module).
not listed are not supported on this module).
not listed are not supported on this module).
not listed are not supported on this module).
Bits
00
01
10
11
Table
10
45-38.
Table 45-37. Commands for MMC/SD/SDIO/CE-ATA cards (continued)
Command Set
Set Bits
Clear Bits
Write Byte
Access Name
adtc
Type
K30 Sub-Family Reference Manual, Rev. 6, Nov 2011
[31:0] stuff bits
Argument
Table 45-38. EXT_CSD Access Modes
The command set is changed according to the Cmd Set field of the argument
The bits in the pointed byte are set, according to the 1 bits in the Value field.
The bits in the pointed byte are cleared, according to the 1 bits in the Value field.
The Value field is written into the pointed byte.
Operation
R1
Resp
SEND_SCR
Abbreviation
Chapter 45 Secured digital host controller (SDHC)
Reads the SD Configuration
Register (SCR).
Description
1345