MC68EN360CAI25L Freescale Semiconductor, MC68EN360CAI25L Datasheet - Page 319

• Manufacturer Part Number: MC68EN360CAI25L
• Description: IC MPU QUICC 25MHZ 240-FQFP
• Manufacturer: Freescale Semiconductor
• Series: MC68000r

Specifications of MC68EN360CAI25L

• Processor Type: M683xx 32-Bit
• Speed: 25MHz
• Voltage: 5V
• Mounting Type: Surface Mount
• Package / Case: 240-FQFP
• Core Size: 32 Bit
• Cpu Speed: 25MHz
• Embedded Interface Type: SCP, TDM
• Digital Ic Case Style: FQFP
• No. Of Pins: 240
• Supply Voltage Range: 4.75V To 5.25V
• Rohs Compliant: Yes
• Family Name: M68xxx
• Device Core: ColdFire
• Device Core Size: 32b
• Frequency (max): 25MHz
• Instruction Set Architecture: RISC
• Supply Voltage 1 (typ): 5V
• Operating Supply Voltage (max): 5.25V
• Operating Supply Voltage (min): 4.75V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 240
• Package Type: FQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / Rohs Status: Compliant

DSSEL—Dynamic RAM Select
SPS1–SPS0—SRAM Port Size (SRAM Bank Only)
PGME—Page Mode Enabled (DRAM Banks Only)
This bit determines if the bank is a DRAM or SRAM, which impacts a number of signals:
1) the length of the cycle is different; 2) address muxing is performed if GAMX = 1; and 3)
the previous RAS is negated if a page bank miss occurs and DSSEL = 1 (for the new
bank).
This attribute determines whether a given chip select responds with DSACKx and, if so,
what port size is returned (see Table 6-13).
If the cycle is terminated by using the internal wait-state attributes, the QUICC drives the
DSACKx lines according to those bits. If the internal wait-state attributes are not used, the
cycle should be terminated with external DSACKx. In this case, the QUICC does not drive
the DSACKx lines, but rather samples them at every falling edge of the clock.
If an MC68EC040 access is performed using this SRAM bank and SPS= 00, 01, or 10,
the SRAM controller operates in the same way, except it asserts TA instead of DSACKx.
If SPS= 11, TA is sampled at every rising edge of the clock.
This bit is used to enable page mode accesses to a DRAM bank. Page mode accesses
are performed only for an internal QUICC or an external QUICC/MC68030-type master.
0 = SRAM bank (i.e., SRAM, EPROM, peripherals, etc.)
1 = DRAM bank
0 = Page mode is disabled.
1 = Page mode is enabled.
If DSACK is provided internally, then the DSACKx lines are still
sampled externally, and can be asserted externally to end the
cycle. However, in this case of external DSACKx assertion, ex-
ternal DSACKx should be asserted and negated prior to when
internal DSACK would have been asserted by the QUICC. This
is easily accomplished on the boot chip select since the QUICC
default value is 14 wait states.
The SRAM controller does not support an external TA response
for MC68040 burst mode. Also, for non-burst MC68040 cycles,
TA cannot be externally asserted before CS is asserted.
Freescale Semiconductor, Inc.
For More Information On This Product,
SPS1–SPS0
Table 6-13. SRAM Port Size
00
01
10
11
MC68360 USER’S MANUAL
Go to: www.freescale.com
32-Bit Port Size
16-Bit Port Size
8-Bit Port Size
External DSACKx Response
NOTES
Result
System Integration Module (SIM60)