MCF5270CAB100 Freescale Semiconductor, MCF5270CAB100 Datasheet - Page 208

• Manufacturer Part Number: MCF5270CAB100
• Description: MCU V2 COLDFIRE 64K SRAM 160-QFP
• Manufacturer: Freescale Semiconductor
• Series: MCF527xr

Specifications of MCF5270CAB100

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 100MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SPI, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 39
• Program Memory Type: ROMless
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 1.4 V ~ 1.6 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 160-QFP
• Processor Series: MCF527x
• Core: ColdFire V2
• 3rd Party Development Tools: JLINK-CF-BDM26, EWCF
• Development Tools By Supplier: NNDK-MOD5272-KIT, NNDK-MOD5270-KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

System Control Module (SCM)
11.3.2 Arbitration Algorithms
There are two modes of arbitration: fixed and round-robin. This section discusses the differences
between them.
11.3.2.1 Round-Robin Mode
Round-robin arbitration is the default mode after reset. This scheme cycles through the sequence
of masters as specified by MPARK[Mn_PRTY] bits. Upon completion of a transfer, the master is
given the lowest priority and the priority for all other masters is increased by one.
If no masters are requesting, the arbitration unit must “park”, pointing at one of the masters. There
are two possibilities, park the arbitration unit on the last active master, or park pointing to the
highest priority master. Setting MPARK[PRK_LAST] causes the arbitration pointer to be parked
on the highest priority master. In round-robin mode, programming the timeout enable and lockout
bits MPARK[13,11:8] will have no effect on the arbitration.
11-10
• The master pointed to by the current arbitration pointer may get on the bus with zero latency
• If a requester will get an immediate address phase (that is, it is pointed to by the current
• There are two arbitration algorithms, fixed and round-robin. Fixed arbitration sets the
• The default priority is FEC (M3) > DMA (M2) > internal master (M1) > CPU (M0), where
• There are two actions for an idle arbitration cycle, either leave the current arbitration
• The anti-lock-out logic for the fixed priority scheme forces the arbitration algorithm to
if the address phase is available. All other requesters face at least a one cycle arbitration
pipeline delay in order to meet bus timing constraints on address phase hold.
arbitration pointer and the bus address phase is available), it will be the current bus master
and is ignored by arbitration. All remaining requesting ports are evaluated by the arbitration
algorithm to determine the next-state arbitration pointer.
next-state arbitration pointer to the highest priority requester. Round-robin arbitration sets
the next-state arbitration pointer to the highest priority requester (calculated by adding a
requester's fixed priority to the current bus master’s fixed priority and then taking this sum
modulo the number of possible bus masters).
M3 is the highest and M0 the lowest priority.
pointer as is or set it to the lowest priority requester.
round-robin if any requester has been held for longer than a specified cycle count.
next +1
next +2
next +3
MCF5271 Reference Manual, Rev. 2
M3 = 11 M2 =01 M1 = 10 M0 = 00
M3 = 00 M2 =10 M1 = 11 M0 = 01
M3 = 01 M2 =11 M1 = 00 M0 = 10
M3 = 10 M2 =00 M1 = 01 M0 = 11
Freescale Semiconductor