DF3052BX25V Renesas Electronics America, DF3052BX25V Datasheet - Page 598

MCU 5V 512K 100-TQFP

DF3052BX25V

Manufacturer Part Number
DF3052BX25V
Description
MCU 5V 512K 100-TQFP
Manufacturer
Renesas Electronics America
Series
H8® H8/300Hr
Datasheets

Specifications of DF3052BX25V

Core Processor
H8/300H
Core Size
16-Bit
Speed
25MHz
Connectivity
SCI, SmartCard
Peripherals
DMA, POR, PWM, WDT
Number Of I /o
70
Program Memory Size
512KB (512K x 8)
Program Memory Type
FLASH
Ram Size
8K x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Data Converters
A/D 8x10b; D/A 2x8b
Oscillator Type
Internal
Operating Temperature
-20°C ~ 75°C
Package / Case
100-TQFP, 100-VQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
DF3052BX25V
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Section 18 ROM
18.5.2
FLMCR2 is an 8-bit register used for flash memory operating mode control. Program-verify mode
or erase-verify mode for addresses H'40000 to H'7FFFF is entered by setting SWE2 to 1 when
FWE (FLMCR1) = 1, then setting the EV2 or PV2 bit. Program mode for addresses H'40000 to
H'7FFFF is entered by setting SWE2 to 1 when FWE (FLMCR1) = 1, then setting the PSU2 bit,
and finally setting the P2 bit. Erase mode for addresses H'40000 to H'7FFFF is entered by setting
SWE2 to 1 when FWE (FLMCR1) = 1, then setting the ESU2 bit, and finally setting the E2 bit.
FLMCR2 is initialized to H'00 by a power-on reset, in hardware standby mode and software
standby mode, when a low level is input to the FWE pin, and when a high level is input to the
FWE pin and the SWE2 bit in FLMCR2 is not set (the exception is the FLER bit, which is
initialized only by a power-on reset and in hardware standby mode). When on-chip flash memory
is disabled, a read will return H'00, and writes are invalid.
Writes are enabled only in the following cases: Writes to bit SWE2 of FLMCR2 enabled when
FWE (FLMCR1) = 1, to bits ESU2, PSU2, EV2, and PV2 when FEW (FLMCR1) = 1 and SWE2
= 1, to bit E2 when FWE (FLMCR1) = 1, SWE2 = 1, and ESU2 = 1, to bit P2 when FWE
(FLMCR1) = 1, SWE2 = 1, and PSU2 = 1.
Bit 7—Flash Memory Error (FLER): Indicates that an error has occurred during an operation on
flash memory (programming or erasing). When FLER is set to 1, flash memory goes to the error-
protection state.
Bit 7: FLER
0
1
Rev. 3.00 Mar 21, 2006 page 568 of 814
REJ09B0302-0300
Bit
Initial value
Read/Write
Flash Memory Control Register 2 (FLMCR2)
FLER
R
7
0
Description
Flash memory is operating normally
Flash memory program/erase protection (error protection) is disabled
[Clearing condition]
Power-on reset or hardware standby mode
An error has occurred during flash memory programming/erasing
Flash memory program/erase protection (error protection) is enabled
[Setting condition]
See 18.8.3 Error Protection
SWE2
R/W
6
0
ESU2
R/W
5
0
PSU2
R/W
4
0
R/W
EV2
3
0
R/W
PV2
2
0
R/W
E2
1
0
(Initial value)
R/W
P2
0
0

Related parts for DF3052BX25V