MPC8536E-ANDROID Freescale Semiconductor, MPC8536E-ANDROID Datasheet - Page 1670

• Manufacturer Part Number: MPC8536E-ANDROID
• Description: HARDWARE/SOFTWARE ANDROID OS
• Manufacturer: Freescale Semiconductor
• Series: PowerQUICC ™r
• Type: MPUr

Specifications of MPC8536E-ANDROID

• Contents: Board
• For Use With/related Products: MPC8536
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Revision History
14.7.1.8, 14-234
17.3.10.5, 17-86
17.4.1.8, 17-103
18.1, 18-1
18.3.1.7, 18-12
19.3.3.2, 19-16
20.4.17, 20-36
20.6.5, 20-58
20.6.6, 50-59
21.3.2.11, 21-22
23.4.1.8, 23-14
23.4.1.20, 23-29
23.4.1.28, 23-37
B-6
MPC8536E PowerQUICC III Integrated Processor Reference Manual, Rev. 1
Added the following note:
SGMII mode utilizes the internal TBI PHY. The internal TBI PHY only
auto-negotiates at 1 Gbps. However, 10 Mbps and 100 Mbps speeds are supported
in SGMII mode. It is recommended that the external PHY inform the MAC if the
desired link speed is not 1 Gbps. Software can perform MII management cycles
to determine the external PHY link speed and program ECNTRL and MACCFG2
accordingly.
Changed access of PCI Express Correctable Error Status Register from read/write
to w1c.
Revised first paragraph by deleting “... originating from the PCI Express outbound
ATMUs,” from the first sentence. Also, deleted the last sentence that stated, "Note
that configuration writes originating from the PCI Express configuration access
registers (PEX_CONFIG_ADDR/PEX_CONFIG_DATA) are not serialized."
Changed Figure 19-1, “eSPI Block Diagram,” to show input clock labeled as
“CCB clock divided by 2” rather than “system clock.”
Added note to SPMODEn fields DIV16n and PMn as follows:
“System clock as used here is defined to be CCB clock divided by 2.”
In register SError (SATA Interface Error Register), made bits 10 and 24 Reserved.
For HOSTVER[VVN], added “0x01 Freescale eSDHC version 2.0”
In Table 20-27, “Commands for MMC/SD,” modified Argument column entry for
ACMD23 to read as follows:
[31:23] stuff bits
[22:0] number of blocks”
Modified existing note in section to read as follows:
“When the internal DMA is not enabled and a write transaction is in operation,
DATPORT must not be read. DATPORT also must not be used to read (or write)
data by the CPU or external DMA if the data will be written (or read) by the
eSDHC internal DMA.”
In description of TXFILLTUNING[TXSCHOH], changed formula (introduction
reads “A good value to begin with is:”) as follows:
TXFIFOTHRES (BURSTSIZE 4 bytes-per-word)
(Formerly contained incorrect term BURSTSIZE
Added new register, GENCFGR, “General Configuration Register”
Updated SVR values for silicon revision 1.1 as follows:
0x803F_0091 for MPC8536E Rev 1.1 (with security)
0x8037_0091 for MPC8536 Rev 1.1 (without security).
Feplaced recommended setting for PCI Express in SRDS1CR2[X3SA–X3SF]
(8 bits in all) with “0” (that is, not disabled)
4 bytes-per-word)
(40
Freescale Semiconductor
TimeUnit)