LPC1837FET256,551 NXP Semiconductors, LPC1837FET256,551 Datasheet - Page 167

• Manufacturer Part Number: LPC1837FET256,551
• Description: Microcontrollers (MCU) 32BIT ARM CORTEX-M3 MCU 136KB SRAM
• Manufacturer: NXP Semiconductors
• Series: LPC18xxr

Specifications of LPC1837FET256,551

• Core: ARM Cortex M3
• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 150MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, SD/MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 80
• Program Memory Size: 1MB (1M x 8)
• Program Memory Type: FLASH
• Eeprom Size: -
• Ram Size: 136K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-LBGA
• Lead Free Status / Rohs Status: Details
• Other names: 935293795551

NXP Semiconductors
Table 107. Pin description
<Document ID>
User manual
Symbol
PC_9
PC_10
PC_11
PC_12
K2
M5
L5
L6
-
-
-
-
…continued
-
-
-
-
-
-
-
-
-
-
-
-
All information provided in this document is subject to legal disclaimers.
[3]
[3]
[3]
[3]
Rev. 00.13 — 20 July 2011
Reset
state
[2]
I; PU
I; PU
I; PU
I; PU
Type Description
-
I
-
I
I/O
-
O
O
-
O
I
-
I/O
-
O
I/O
-
I
I
-
I/O
-
-
I/O
-
-
O
-
I/O
-
I/O
I/O
R — Function reserved.
USB1_ULPI_NXT — ULPI link NXT signal. Data flow
control signal from the PHY.
R — Function reserved.
ENET_RX_ER — Ethernet receive error (MII interface).
GPIO6[8] — General purpose digital input/output pin.
R — Function reserved.
T3_MAT2 — Match output 2 of timer 3.
SD_POW — <tbd>.
R — Function reserved.
USB1_ULPI_STP — ULPI link STP signal. Asserted to
end or interrupt transfers to the PHY.
U1_DSR — Data Set Ready input for UART 1.
R — Function reserved.
GPIO6[9] — General purpose digital input/output pin.
R — Function reserved.
T3_MAT3 — Match output 3 of timer 3.
SD_CMD — SD/MMC command signal.
R — Function reserved.
USB1_ULPI_DIR — ULPI link DIR signal. Controls the
ULP data line direction.
U1_DCD — Data Carrier Detect input for UART 1.
R — Function reserved.
GPIO6[10] — General purpose digital input/output pin.
R — Function reserved.
R — Function reserved.
SD_DAT4 — SD/MMC data bus line 4.
R — Function reserved.
R — Function reserved.
U1_DTR — Data Terminal Ready output for UART 1. Can
also be configured to be an RS-485/EIA-485 output
enable signal for UART 1.
R — Function reserved.
GPIO6[11] — General purpose digital input/output pin.
R — Function reserved.
I2S0_TX_SDA — I2S transmit data. It is driven by the
transmitter and read by the receiver. Corresponds to the
signal SD in the I
SD_DAT5 — SD/MMC data bus line 5.
Chapter 12: LPC18xx Pin configuration
2
S-bus specification.
UM10430
© NXP B.V. 2011. All rights reserved.
167 of 1164