LPC1837FET256,551 NXP Semiconductors, LPC1837FET256,551 Datasheet - Page 864

• Manufacturer Part Number: LPC1837FET256,551
• Description: Microcontrollers (MCU) 32BIT ARM CORTEX-M3 MCU 136KB SRAM
• Manufacturer: NXP Semiconductors
• Series: LPC18xxr

Specifications of LPC1837FET256,551

• Core: ARM Cortex M3
• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 150MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, SD/MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 80
• Program Memory Size: 1MB (1M x 8)
• Program Memory Type: FLASH
• Eeprom Size: -
• Ram Size: 136K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-LBGA
• Lead Free Status / Rohs Status: Details
• Other names: 935293795551

NXP Semiconductors
<Document ID>
User manual
37.7.10 I
37.7.9 I
In monitor mode, the I
the ENA_SCL bit is not set. This means that the processor will have a limited amount of
time to read the contents of the data received on the bus. If the processor reads the DAT
shift register, as it ordinarily would, it could have only one bit-time to respond to the
interrupt before the received data is overwritten by new data.
To give the processor more time to respond, a new 8-bit, read-only DATA_BUFFER
register will be added. The contents of the 8 MSBs of the DAT shift register will be
transferred to the DATA_BUFFER automatically after every nine bits (8 bits of data plus
ACK or NACK) has been received on the bus. This means that the processor will have
nine bit transmission times to respond to the interrupt and read the data before it is
overwritten.
The processor will still have the ability to read DAT directly, as usual, and the behavior of
DAT will not be altered in any way.
Although the DATA_BUFFER register is primarily intended for use in monitor mode with
the ENA_SCL bit = ‘0’, it will be available for reading at any time under any mode of
operation.
Table 812. I
The four mask registers each contain seven active bits (7:1). Any bit in these registers
which is set to ‘1’ will cause an automatic compare on the corresponding bit of the
received address when it is compared to the ADRn register associated with that mask
register. In other words, bits in an ADRn register which are masked are not taken into
account in determining an address match.
On reset, all mask register bits are cleared to ‘0’.
The mask register has no effect on comparison to the General Call address (“0000000”).
Bits(31:8) and bit(0) of the mask registers are unused and should not be written to. These
bits will always read back as zeros.
When an address-match interrupt occurs, the processor will have to read the data register
(DAT) to determine what the received address was that actually caused the match.
Bit
7:0
31:8
2
2
C Data buffer register
C Mask registers
Symbol Description
Data
-
0x400E 002C (I2C1)) bit description
2
C Data buffer register (DATA_BUFFER - address 0x400A 102C (I2C0) and
This register holds contents of the 8 MSBs of the DAT shift
register.
Reserved. The value read from a reserved bit is not defined.
All information provided in this document is subject to legal disclaimers.
2
Rev. 00.13 — 20 July 2011
C module may lose the ability to stretch the clock (stall the bus) if
Chapter 37: LPC18xx I2C-bus interface
UM10430
© NXP B.V. 2011. All rights reserved.
Reset value
0
-
864 of 1164