LPC1837FET256,551 NXP Semiconductors, LPC1837FET256,551 Datasheet - Page 784

• Manufacturer Part Number: LPC1837FET256,551
• Description: Microcontrollers (MCU) 32BIT ARM CORTEX-M3 MCU 136KB SRAM
• Manufacturer: NXP Semiconductors
• Series: LPC18xxr

Specifications of LPC1837FET256,551

• Core: ARM Cortex M3
• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 150MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, SD/MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 80
• Program Memory Size: 1MB (1M x 8)
• Program Memory Type: FLASH
• Eeprom Size: -
• Ram Size: 136K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-LBGA
• Lead Free Status / Rohs Status: Details
• Other names: 935293795551

NXP Semiconductors
<Document ID>
User manual
34.7.3.1 Setup and hold time requirements on CS with respect to SK in Microwire
latches each bit on the rising edge of SK. At the end of the frame, for single transfers, the
CS signal is pulled HIGH one clock period after the last bit has been latched in the receive
serial shifter, that causes the data to be transferred to the receive FIFO.
Note: The off-chip slave device can tristate the receive line either on the falling edge of
SK after the LSB has been latched by the receive shiftier, or when the CS pin goes HIGH.
For continuous transfers, data transmission begins and ends in the same manner as a
single transfer. However, the CS line is continuously asserted (held LOW) and
transmission of data occurs back to back. The control byte of the next frame follows
directly after the LSB of the received data from the current frame. Each of the received
values is transferred from the receive shifter on the falling edge SK, after the LSB of the
frame has been latched into the SSP.
mode
In the Microwire mode, the SSP slave samples the first bit of receive data on the rising
edge of SK after CS has gone LOW. Masters that drive a free-running SK must ensure
that the CS signal has sufficient setup and hold margins with respect to the rising edge of
SK.
Figure 107
rising edge on which the first bit of receive data is to be sampled by the SSP slave, CS
must have a setup of at least two times the period of SK on which the SSP operates. With
respect to the SK rising edge previous to this edge, CS must have a hold of at least one
SK period.
Fig 106. Microwire frame format (continuous transfers)
Fig 107. Microwire frame format setup and hold details
CS
SO
SK
SI
illustrates these setup and hold time requirements. With respect to the SK
All information provided in this document is subject to legal disclaimers.
LSB
CS
SK
SI
0
MSB
Rev. 00.13 — 20 July 2011
output data
4 to 16 bits
LSB
MSB
t
HOLD
8-bit control
= t
SK
t
SETUP
=2*t
SK
Chapter 34: LPC18xx SSP0/1
LSB
MSB
output data
4 to 16 bits
UM10430
© NXP B.V. 2011. All rights reserved.
LSB
784 of 1164