MPC561MZP56 Freescale, MPC561MZP56 Datasheet - Page 1227

• Manufacturer Part Number: MPC561MZP56
• Manufacturer: Freescale

Specifications of MPC561MZP56

• Cpu Family: MPC56x
• Device Core: PowerPC
• Device Core Size: 32b
• Frequency (max): 56MHz
• Interface Type: QSPI/SCI/SPI/UART
• Total Internal Ram Size: 32KB
• # I/os (max): 56
• Number Of Timers - General Purpose: 22
• Operating Supply Voltage (typ): 2.6/5V
• Operating Supply Voltage (max): 2.7/5.25V
• Operating Supply Voltage (min): 2.5/4.75V
• On-chip Adc: 2(32-chx10-bit)
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 388
• Package Type: BGA
• Program Memory Type: ROMLess
• Program Memory Size: Not Required
• Lead Free Status / RoHS Status: Not Compliant

F.6
Note: (V
Freescale Semiconductor
18
19
20
21
22
23
24
25
26
27
1
2
3
1
2
3
4
5
6
7
8
9
This parameter is periodically sampled rather than 100% tested
Up to 0.5 V during power up/down.
To obtain full-range results, V
When using the QADC in legacy mode it is recommended to connect this pin to 2.6V or 3.3V, however it can be
connected to 0V or 5V without damage to the device.
A resistor must be placed in series with the IRAMSTBY power supply. Refer to
Guidelines.”
All injection current is transferred to the V
power supply within the specified voltage range.
Absolute maximum voltage ratings for each pin (see
Total injection current for all I/O pins on the chip must not exceed 20 mA (sustained current). Exceeding this limit can
cause disruption of normal operation.
Current refers to two QADC64 modules operating simultaneously.
Below disruptive current conditions, the channel being stressed has conversion values of 0x3FF for analog inputs
greater than V
presence of the sample amplifier. Other channels are not affected by non-disruptive conditions.
Assumes stable power and oscillator.
F
Estimated value, real values to be characterized and updated.
VCOOUT
DD
Oscillator Startup time (for typical crystal capacitive load)
4-MHz crystal
20-MHz crystal
PLL Lock Time
PLL Operating Range
Crystal Operating Range, MODCK=0b010,0b110
MODCK[1:3] = 0b001, 0b011, 0b100, 0b101, 0b111
PLL Jitter
PLL Jitter (averaged over 10 µs)
Limp Mode Clock Out Frequency
Oscillator Bias Current (XTAL)
4 MHz
20 MHz
Oscillator Drive (XTAL)
Oscillator Bias Resistor
Oscillator and PLL Electrical Characteristics
= 2.6 V ± 0.1 V, V
is 2x the system frequency.
RH
and 0x000 for values less than V
DDH
Characteristic
2
= 5.0 V ± 0.25 V, T
SSA
MPC561/MPC563 Reference Manual, Rev. 1.2
≤ V
RL
≤ V
Table F-5. Oscillator and PLL
DDH
INDC
. An external load is required to dissipate this current to maintain the
A
= T
≤ V
RL
L
RH
Table
. This assumes that V
to T
≤ V
H
)
DDA
F-1) must also be met during this condition.
OSCstart20
OSCstart4
F
F
Symbol
CRYSTAL
VCOOUT
T
F
R
I
I
F
LOCK
BIAS
JIT10
OSC
—
OSC
JIT
RH
-0.3%
| 1.5 |
≤ V
Min
-1%
0.5
30
15
Appendix C, “Clock and Board
3
—
3
7
3
DDA
and V
Typica
11
1
l
RL
≥ V
Electrical Characteristics
SSA
+0.3%
1000
| 0.8 |
| 4.0 |
+1%
Max
112
17
10
10
25
—
5
3
due to the
3
1
Clocks
Input
MHz
MHz
MHz
MHz
Unit
MΩ
mA
mA
mA
ms
ms
—
F-11