MPC561MZP56 Freescale, MPC561MZP56 Datasheet - Page 987

• Manufacturer Part Number: MPC561MZP56
• Manufacturer: Freescale

Specifications of MPC561MZP56

• Cpu Family: MPC56x
• Device Core: PowerPC
• Device Core Size: 32b
• Frequency (max): 56MHz
• Interface Type: QSPI/SCI/SPI/UART
• Total Internal Ram Size: 32KB
• # I/os (max): 56
• Number Of Timers - General Purpose: 22
• Operating Supply Voltage (typ): 2.6/5V
• Operating Supply Voltage (max): 2.7/5.25V
• Operating Supply Voltage (min): 2.5/4.75V
• On-chip Adc: 2(32-chx10-bit)
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 388
• Package Type: BGA
• Program Memory Type: ROMLess
• Program Memory Size: Not Required
• Lead Free Status / RoHS Status: Not Compliant

To read control or status from memory-mapped locations the following sequence would be required.
For a block write to memory-mapped locations the following sequence would be required.
For a block read from memory-mapped locations the following sequence would be required.
Refer to
24.6.3
To write control or status data to READI tool mapped registers the following sequence would be required.
To read control or status from READI tool mapped registers the following sequence would be required
Refer to
24.6.4
Registers may be updated via the auxiliary port using the download request message with the message
containing only N (where N is less than register width) most-significant bits of the register. In such cases
the bits not transmitted will be reset to 0b0. The bits transmitted will be aligned such that the last bit
transmitted will be the most significant bit of the register. Therefore a message size that is divisible by the
input port size should be transmitted.
Freescale Semiconductor
1. The tool confirms that the device is ready. The tool transmits the download request public message
2. When device reads data it transmits upload/download information message (TCODE 19)
1. The tool confirms that the device is ready. The tool transmits the download request public message
2. The tool waits for device ready for upload/download message (TCODE 16). When it is transmitted
1. The tool confirms that the device is ready. The tool transmits the download request public message
2. The tool waits for upload/download information message (TCODE 19) from device, which
1. The tool confirms that the device is ready. The tool transmits the download request message
2. The tool waits for device ready for upload/download message (TCODE 16) before initiating next
1. The tool confirms that the device is ready. The tool transmits the upload request message (TCODE
2. When device reads data it transmits upload/download information message (TCODE 19)
(TCODE 18) which contains read attributes and target address.
containing read data. Device is now ready for next access.
(TCODE 18) which contains block write attributes, first write data, and target address.
by device, tool transmits upload/download information message (TCODE 19) containing next
write data. This step is repeated until all data is written
(TCODE 18) which contains block read attributes and target address.
contains read data. This step is repeated until all data is read.
(TCODE 18) which contains write data, and register opcode.
access.
17) which contains the target opcode.
containing read data. Device is now ready for next access.
Section 24.10, “Read/Write
Section 24.10, “Read/Write
Accessing READI Tool Mapped Registers Via the Auxiliary Port
Partial Register Updates
MPC561/MPC563 Reference Manual, Rev. 1.2
Access,” for more details on read/write access protocol.
Access,” for more details on read/write access protocol.
READI Module
24-19